Brand: Samsung

Seems like some of the water is draining, and did check the pump, it’s not the issue. Checked the chopper and did find a lot of debris so I cleared that out and ran another test cycle. Thought maybe the disposal was the issue since they had a new one, but the knock out was removed already. Still having some issues. Seems to start pumping and then slows down until it completely stops, leaving a little bit in there.

Unit is no longer cooling & I know it’s the evaporator assembly. Haven’t done many of these, any helpful tips?

This ice maker is working and producing but not dispensing through the door. I’ve narrowed it down to the actual dispenser assembly and door flapper but now am having an impossible time finding the part on the schematic. Any chance you can do the lookup for me and get me pricing for it’s replacement?

The customer can’t use the oven, but I’m also having trouble finding this replacement part available from my usual vendors. I noticed you didn’t either. Is it a DG66-00017A? At least want to confirm that.

I think this needs a new idler pulley and belt but I can’t find the correct part numbers. Does someone have time to pull them for me? Thank you.

I need a brake case and case sensor assembly do get this unit working properly again, do you guys carry them?

Found the belt shredded last year and replaced it, but seems to have happened again. How can it be going through them so fast since the customer doesn’t use it on that consistent of a schedule? I can replace the belt again but don’t want to do this every year. and cover the cost of the part if something else is going on.

Control panel LEDS are flashin On, , Off, On. This happens right after the unit fills, then drains and refills. I have changed the case sensor and water valve. I am leaning to a new flow meter before I take this unit out. Any help would be greatly appreciated.

Found a failed termistor & hi limit fuse, do you have any part information on this model?

This need the thermistor and fuse, do you guys carry both?

I’m almost positive this is the control board, do you guys carry that part?

Is this pump correct for this unit? DC31-00054A

I have a GE Fridge MN:PFFSS6PKWBSS, SN: AR075158. The IM produces a few batches of ice per day. The IM cycles when I hold down the cycle button for 10 seconds and it fills with water. The duct seems to have good airflow to the compartment and the sensor mounted in the back checks out fine. Any ideas?

I have a Samsung refrigerator. This is a French door unit.
The back panel in the fresh food compartment was solid ice the evaporator fan blade was frozen half way up.
I pulled the plug defrosted the back took it out. Replaced the evaporator fan. Plugged it back in the display, located inside at top showed 88 on the freezer side of control and the fresh food side of control. The evaporator fan was not running. I did have both doors open about 3 hours and ran a steamer inside to defrost the back panel.
The settings will not respond at all and the fan is not running. Is there something I need to reset? Thanks In advance

I have a Samsung Refrigerator Model: RS2555SL/Xaa
Needs a new refrigerator defrost heater. When I look it up I see you have to purchase the whole evaporator to get the defrost heater (not sold separately)
Are you guys separating the defrost heater from the evaporator when it comes in and then replacing it out with the old one, or are you replacing the entire evaporator for just a simple defrost heater? Any suggestions would be greatly appreciated.

Found this unit needing a new rear bearing, but cost of the repair exceeds the value of the unit. Does this happen to anyone else? The parts are expensive and I don’t do many of them due to this happening.

What does this error normally mean?

I got there and found the evaporator motor bad. I also found what appears to be a bad temp sensor. Do you have information on both for me?

I replaced the touchpad initially thinking that was it, but still happening. Now I’m realizing it’s the main control board and my own guys suggested maybe a case sensor. Do you have the part information on both?

I checked everything out and this unit needs a new icemaker. Anyone have time to do a quick lookup for me? I’ll need to order it asap to get this done. Appreciate it.

I think this needs the heating element replaced but I can’t find the part for it.

I cleared the defrost drain and replaced the defrost sensor thinking and hoping that would work but am still getting some water now a few days later. Am I missing something?

I think it’s the belt but am unsure how to even get to it. Possible idler pulley too that I may need to take with me just in case.

We smelled a burning rubber smell and that when she opened the door smoke billowed out. It wasn’t anything to do with the laundry. Any thoughts as to what this could be?

One of our techs is having an issue with a Samsung DW model listed above, the unit fills up, then drains, then fills and then the following lights start flashing all at once (Normal, Heavy and Quick lights). Customers complaint was unit making grinding noise and would not clean, but the pump never starts up. The tech disassembled the top of the sump and no debris was found and the impellar turns freely. Any help would be greatly appreciated.

How does one adjust the water fill level on this ice maker? Thank you for your replies.

I think I’ve got this narrowed down to needing a main control board and the turbidity sensor, but can’t find the part information. Anyone available to take a look?

This unit had an ice build up in the FF evaporator fan area. I ohmed out the heater and it was good, I replaced the thermistor and thermal fuse. I have received conflicting information that the thermistor should be moved to as high a location as possible on the evaporator lines and also that it should be moved down to the middle of the evaporator and the main board should be changed as well? The thermistor wires are very short and cannot move very far. The part number is DA32-00029Q. I’m sure there is another workable part number with longer wires. . There were no error codes. FF section had warmed up. Evaporator fan was stuck in ice.

Samsung Hudson Electric Dryer DV422EWHDWR, I need error codes and diagnostic chart or videos. Thanks in advance

Model DMT300RFS/XAA
When it starts, the water comes in in measured amounts, but in a few minutes is to the point of flooding the tub edge. The unit then faults out with the ‘Heavy” and “Quick” lights flashing. This shows to be a ‘flow meter error”. Can someone who is familiar with these units expain the fill cycle on this model? I was able to vacuum out the water and then the unit would go into diagnostics. The wash motor and drain motors work fine from the service cycle, but nce the unit overfills, the control is useless. They should have made this unit go directly into a pump-out instead of freezing up full of water, in my opinion.
Any advice on how to solve the overfill issue? It’s not the valve…