0 votes
106 views

After make ice and fill bin start melting ice completely

0 votes
304 views

the lights are on. water is running, but the ice maker is not making any ice.

  • lue asked 11 months ago
  • last active 11 months ago
0 votes
252 views

Lights are out, Will not produce ice, Unit will not run.

0 votes
200 views

The ice maker may stop making ice if Max Ice is selected.

0 votes
332 views

Need help looking for service manual ZDIS150ZSSE, ZDIC150ZBBE , ZDIS15SSHALH , ZDIS15SSHARH

0 votes
337 views

Need service manual on UCC15NJII Stand alone Ice maker

0 votes
567 views

Need service manual on GE nugget Ice maker UNC15NJ

0 votes
311 views

I have A Haier ice maker that is not dropping ice.

0 votes
417 views

I have a Scotsman stand alone ice machine it is producing ice but the ice cubes seem hollow. It seems like it is completing the cycle to quick.

  • chucks asked 2 years ago
  • last active 2 years ago
0 votes
263 views

My LG range wont heat up at all.

0 votes
835 views
0 votes
433 views

Customer complaint is the cubes are small, and only a handful of small cubes unit runs fan runs.
Have not checked the unit yet, do you have a service manual on this Scotsman stand alone ice maker unit.
Any advise and service information would be helpful as I have not checked the unit yet. Thank you in advance for your help.

  • billtilley asked 2 years ago
  • last active 2 years ago
0 votes
551 views

Sir,
the ice maker is warm inside the cabinet and it is making a surge of water noise.
The unit was working fine and then stop.
The unit has been cleaned and its still not working.
PLEASE HELP

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
410 views

what should I test or part I should try

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
429 views

drain pump kicks on and all the water is pumped out and of course the machine stops and doesn’t finish the ice

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
732 views

Hello,
A few months ago, I ran the cleaning cycle on our ice maker. After it completed, everything returned to normal and all seemed fine. Within about couple of days, I noticed a mildew smell coming from the bin. The ice did not smell but there was a nasty moldy smell coming from somewhere inside the bin. I replaced the all the hoses (drains, recirculation hoses, etc) because they looked cloudy and a little nasty. I also found the writing harness from the control box to the connector bracket had a wire that was loose in the harness due to corrosion. I replaced that harness. Put everything back together and everything was fine for a couple of days but the mildew smell came back. I did some deeper checking of things and found a couple of issues.

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
649 views

I have an issue with a Ice Maker, it’s a Whirlpool and this is the problem I am seeing: Uneven Ice cubes

0 votes
635 views

Unresponsive

0 votes
477 views

Having an issue with an Ice Maker

0 votes
555 views

Having an issue with an Ice Maker

0 votes
704 views

Hello I have a question on a Whirlpool Ice Maker. I’m noticing these issues: Block of ice on Freeze Plate

0 votes
491 views

Light is out.

0 votes
801 views

My Whirlpool dishwasher will not run

0 votes
566 views
0 votes
858 views

why is this unit not making ice cubes

  • Guest asked 3 years ago
  • last active 3 years ago
0 votes
788 views

The problem was that it was not making ice. It is a KitchenAid under counter ice maker. I put it through the self cleaning cycle twice and after it made ice, but then the customer called back saying it didn’t make ice after I left. When I went back I unplugged it for a few minutes then plugged it back in it would make ice one time then quit again. The ice maker does not have a tech sheet to run self diagnostics. Does anybody have a tech sheet or know where I can get one? Do I have a bad PCB? Does anyone know what is wrong with this? Also there is a ice wall in the back, is this supposed to be there? It is solid covering the back so I cannot reach back there without breaking it, which I do not want to do if it is supposed to be there.

Showing 1 - 30 of 41 results