0 votes
3k views

I have a bosch dishwasher showing an E24 code. What does this mean?

0 votes
2k views

THIS BOSCH REFRIGERATOR IS ONLY INTERMITTENTLY MAKING ICE. CHECKED THE FREEZER TEMPS AND THE FREEZER TEMPS ARE NORMAL AND IN RANGE. IS THERE ANYTHING ELSE ON THESE UNITS THAT CAN PREVENT IT FROM MAKING ICE BESIDES THE ICE MAKER OR THE WATER VALVE?

0 votes
3k views

My dishwasher doesn’t want to drain completely. Initially I thought it was something stuck and cleaned out as far as possible down into the impeller or chopper area like a video I saw on here. Ran another cycle and same thing happened. Could it be something stuck further in the drain or pump area?

  • Noelle asked 9 years ago
  • last active 9 years ago
0 votes
2k views

This dishwasher was just re-installed after a kitchen remodel. I got called out because it wasn’t draining. I removed the knockout from the disposal the first time thinking that was the issue. Turns out it wasn’t, still having issues. This time I’m getting a bad pump but cannot find the part number anywhere. Somebody there able to look it up for me?

0 votes
2k views

My Bosch dishwasher is not heating and wont stop running.

0 votes
2k views

Door lock won’t unlock? It makes a clicking noise like is trying to unlock but can’t. Does this mean the locks bad? In diagnostic mode can you test the lock?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My Bosch dishwasher is not getting any water.

0 votes
2k views

Door latch buzzes 3 times and won’t unlock
No error code comes up

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

The dishwaher will not drain.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Door is heavy, door will not close, leaks water.

0 votes
18k views

Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views

Initially costumer had a clogged drain and over frosted rear panel so i figured its due to a clogged drain like Samsungs get frosty in the fresh food when drain is clogged, Cleaned drain and made sure everything was good but over frosting came back. THE SHEET OF ICE ON FREEZER FLOOR HAS NOT RETURNED so clearly not clogged drain but frost is back??!

(This brand was not on the selectable list but im sure you guys have serviced these or the Meile brand which appears to be identical internally, And am i paying for the monthly membership plus for every questions?..)

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
3k views

I have a E01 error code on a Ascenta Dishwasher? any suggestions

  • Rany asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Wanted to let you guys know, we’ve had a couple Bosch’s with this complaint, and there’s been nothing wrong after diagnosing. We always check wiring, controls, motor, and heater. No stored error codes, and all safety checks come back ok. Just in case you see any out there, let us know if you actually find a problem!

0 votes
2k views

Bosch DW leaking at bottom corners of door. Checked for lower door seal but see nothing listed. Does anyone know if there is a replacement part for the seal at the bottom of the door?
Maybe there is a different fix for this? Any information is appreciated.

0 votes
2k views

Looked at above Bosch dishwashers, did not find wire diagram in either one. I thought they were stuck in a pocket in the base behind the toe plate. Not behind outer door panel, so anyplace else I should look?
Customer says it doesn’t clean and dishes are not hot like before. I did the following checks while it was washing. Heater circuit (R – W/R wires) had 120vac and 9 amps. NTC (O-O wires) was at 25.56k ohms and water was 95 degrees. Wash motor was pulsing, I am thinking the washer is trying to heat the water. Does anyone have a wire diagram / tech sheet for this model? Any suggestions on what to look for?
This unit has a timer, so I checked all wires on the timer. To ground, B, W/R, PU, GY, AND GY/B all had 120vac. GY/B had 8.86 amps at one point. I am guessing this is the heater circuit? A thermostat on top of the door inner panel (W – Y wires) was open.
Anyone with a wire diagram / tech sheet for this model? Any suggestions on what to look for?

0 votes
2k views

Problem with a Bosch Dishwasher

0 votes
2k views

Oven does 2things,
1. It takes a long time (30 minutes) to raise temperature. Set oven at 375*. 30 minutes later it reads 310* then starts to drop to 295*. I put an oven thermostat inside and it read 170*.
2. Once it reaches a high temperature ( below set temperature ) it begins to drop.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

No lites on display panel

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Door stays open

0 votes
4k views
e21

so the unit is getting an e 21 error. i put it into the diagnostic test mode and it will not go past s01
please advise

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
2k views

I checked this unit out and only found that there seemed to be a build up of dish soap inside somehow. Assuming customer is soaking or rinsing dishes before loading and it’s migrating into the dishwasher, causing a lot of suds, and not very adequate cleaning cycles. What do you guys normally recommend to clear them? Is there a specific product you use?

0 votes
2k views

This unit flags the clogged drain error and the washer still has soap in it when there error is displayed. I thought it might be a faulty pump so I replaced it but the error still shows up. When the dial is set to drain it flushes the water in a hurry every time.
Thanks for anyones input,

0 votes
3k views

Customer says it spins ok cycle finishes ok, the vent sends cold air out and clothes are not dry.
My first thought was to check the heat element and thermal cutoff. Unfortunately, when I spoke with Bosch, they said they dont make the heating element for this anymore and there is no replacement part number. Would you test both first ? what would test second ?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Problem with a Bosch Dishwasher

1 vote
1k views

I checked the ohms on this temp probe and it read 1080. I was told that it should read at least 1100 at room temperature.
Is the probe ” bad ” at a 1080 reading “
Would it cause a delay in raising the oven temperature to 350 at set temperature? A delay of 30 minutes and the oven never reached its set temperature. Plus, when the temperature rose to about 310* it began to drop gradually to 295*

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Unit doen’t complete the cycle and stop in the middle. Do we need a main board? It drains good.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

will not fill, bas smell, slow fill.

0 votes
1k views

I have a Bosch gas range. The display/control panel stopped working. The igniters on stove work so can still cook, but can not operate the oven.

0 votes
1k views

I am having a problem getting into machine need service manual breakdown or video of disassembly.

  • Guest asked 5 years ago
  • last active 5 years ago
Showing 31 - 60 of 151 results