My Whirlpool dryer will not start,any suggestions?
- David Sutton asked 10 years ago
- last active 10 years ago
My ice maker in my Whirlpool refrigerator is not working.
- Gary Williams asked 10 years ago
- last active 10 years ago
My Whirlpool washer will not turn on and is completely unresponsive. Any suggestions?
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
My Whirlpool dryer will not start, just makes a humming noise.
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
My Whirlpool washer is not spinning. Any suggestions?
- Harley Clark asked 10 years ago
- last active 10 years ago
My Whirlpool washer is making loud grinding noises, any suggestions?
- Harley Clark asked 10 years ago
- last active 10 years ago
The customer called after he changed water valve and dispenser actuator. He said that it showed a eo2 and fo8. When I went there the machine will start lock door and tub will start turning. The whole time it is running the dispenser actuator is turning and never stops. It just turns and turns and doesn’t stop at a place to take on water. Any help would be greatly appreciated .
- Guest asked 10 years ago
- last active 10 years ago
Machine was dead. Changed ccu. Panel lights up and responds but shuts off after 5 seconds. No water enters and dispenser doesn’t move. Will work in drain and spin
- Guest asked 10 years ago
- last active 10 years ago
My Whirlpool refrigerator is leaking water. Any suggestions?
- Don Kopecky asked 10 years ago
- last active 10 years ago
Customer brought washer said was not draining properly. When we tried washer made humming sound lid lock kicks in and out then no water comes in and nothing happens. lid switch light stays flickering
- Guest asked 10 years ago
- last active 10 years ago
We have a Whirlpool dishwasher, above model, runs to about 1/2 way thru cycle and shuts off, cancel drain light blinks continuously. Any help/ advice we can get with this unit would be appreciated.
Thanks in advance
- David Sutton asked 10 years ago
- last active 10 years ago
Need service manual. Wonder if the freezer door SW controls the evaporator fan, light and something else?
Alex
- Guest asked 10 years ago
- last active 10 years ago
REAR WATER INLET TUBE FREEZES UP, THEN FREEZES RECEIVING CUP AND REAR END OF FREEZER. HAVE DEFROSTED AREA THEN GET ONE LOAD OF ICE, THEN IT FREEZES UP AGAIN.
- Guest asked 10 years ago
- last active 10 years ago
I hear clicking but not lighting
- Guest asked 10 years ago
- last active 10 years ago
My Whirlpool dryer is not heating.
- Curtis Appliance Repair asked 10 years ago
- last active 10 years ago
My Whirlpool refrigerator is leaking.
- T&G Appliance Repair asked 10 years ago
- last active 10 years ago
My Whirlpool dryer starts up but will not tumble.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
Some of the buttons on the touchpad of my Whirlpool dishwasher are unresponsive.
- T&G Appliance Repair asked 10 years ago
- last active 10 years ago
The door on my whirlpool dryer will not stay shut.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
Hey guys, anybody worked on this Italian made whirlpool washer LHWOO5PQ4 serial
cat2611315? Its 240 volts ? Not starting has 240 volts
- Gary Williams asked 10 years ago
- last active 10 years ago
We would appreciate some advice on this unit.
A few weeks back it was faulting out with an F71.
We replaced the MCU it ran fine for the few weeks.
This is a well used unit in a care facility.
New complaint “not spinning enough” It will run thru cycle till final spin, 13 mins left in cycle. It will spin slowly and not advance past the 13 mins on display.Not showing a fault code.
It will spin in the test cycle.
Any advice would sure be appreciated.
- Gary Williams asked 10 years ago
- last active 10 years ago
My Whirlpool dryer is making loud noise when the drum is turning.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
My gas whirlpool dryer will not stay hot.The burners come on and off every 5-seconds.
- Harley Clark asked 10 years ago
- last active 10 years ago
Washer lights up and locks in diag mode stops at C 3. When repowered got error code E 1 F6. Replaced control same issue manual is not useful checked power supplies both were okay.
door lock stays lock most times until times out. Won’t go into diagnostics that far very inconsistent results. Never get drain or main stator motor to run …I get a quick shot of 120 at the motor on start up
but nothing on motor test c5. I checked motor ohms and harness to mcu seems good.
what is the next step ?
- T&G Appliance Repair asked 10 years ago
- last active 10 years ago
