Brand: Whirlpool

good starting point to troubleshoot this brand new machine…120v ac each leg including feeding back through neutral.5 volts difference between right hot leg and neutral. what the??????

We are having an issue with this wall oven showing an F6E0 error code when going into the diagnostic mode. After researching, we found it is an issue with the boards or control panel. Is there any way to test which is the faulty part causing this issue?

replaced 4 suspension and the sensor problem not fixed
what do you think is the problem

To whom it may concern,
I have a Whirlpool WRF757SDEM refrigerator that has cooling issues in the refrigerator section of the unit;not the freezer . The bottom fresh drawer is ~ 33 degrees, the 3 drawers above that are ~ 40 degrees and the upper main is ~ 47 degrees.These temperatures have been verified by placing thermometers in each section. Due to this elevated temperature we also have had to shut the iced maker off as the ice would melt in the door compartment causing water to run out the chute. I have had a large amount of ice forming behind the bottom drawer ( the one at ~ 33 degrees) and have had to remove this 3 times as it build up there and has caused issues shutting that drawer. The ice was in all the vents located there and I had to take care so it would not get damaged. The freezer portion of this unit works fine and freezes ice in ~ 30 minutes.
I am hoping there is a repair for this erratic cooling as the unit is barely 6 years old and is just out of warranty.
Any and all assistance would be greatly appreciated.

This unit is on city water and the city flushed the line and muddy water stopped up the filter. The customer replaced the filter and that is when the ice maker production almost stopped. I performed the harvest test and the water valve test and replaced the valve part # wpw10341329. I retested the water valve and it turned on and off OK. The nest day the customer called and said it still only made about 4 cubes. Does the water valve fill test deliver the precise amount of water in the test mode? What else can I test or do?

The washer works in any mode, until spin cycle. It will agitate, but stops every time when it gets to spin cycle. The washer was locked, stopped, and would not turn on again. What is causing this?

Do you have a tech manual for fridge model WSF26C3EXF01 thanks

i need the tech sheet for this one

Water in unit not getting heated and not drying dishes, element not coming on.

The washer just stops at 17 minutes left on all selections except bulky items. It will run the entire load on bulky items. There are no stored error codes and the unit completes the automatic diagnostic mode with no problems.

No power at all, already checked the fuse and it’s good.

How do I unlock bottom door.
I can remove oven because it is not mounted to cabinet with screws. It takes two people unless there is another way using dolly or other method.
I believe safety thermal fuse has blown. What location is fuse.

The user interface on this oven will not work at all. Acts completely dead. No clock display, and none of the buttons work, unless you turn any of the burners on. Then the touch pads work correctly. Then you can set the oven to a temperature and it will say preheat for about 5 seconds then the display goes dead again. One more thing the burners never actually heat up when you turn them on and if you turn the burner off during any of this the screen goes dark and acts like it has no power.

What is room temperature resistance for the refrigerator thermistor?

how to put the electronic defrost control into defrost manually?

GOOD MORNING. WHEN I GOT THERE THE WASHER HAD WATER IN THE TUB. I PUT THE DIAL ON SPIN AND DRAIN AND PRESSED START. AT THIS POINT FOR ABOUT 2 SECONDS I HEARD THE PUMP ENGAGE AND SOME WATER CAME THROUGH THE LINE. IT THEN STOPPED AND TRIED TO START THE SPIN CYCLE, BUT THEN IT CUT OFF. I TESTED VOLTAGE TO PUMP AND FOUND 110 VOLTS AT ALL TIMES, EVEN WHEN THE WASHER WAS NOT IN ANY CYCLE. PULLED OUT THE PUMP AND PUT 110 VOLTS TO IT AND IT WAS SPINNING WELL. ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.

The refrigerator works perfect, except about every hour I get a 1 minute buzz for the evaporator fan motor then it stops and blows normal. Whirlpool Refrigerator

No water I checked the primary valve its good but no voltage. I checked the ice and water valves inside the door. good and getting voltage. Not sure how this works but the circuit diagram shows the Pilot valve is powered from the main PCB and the ice and water valves are powered from the PWB Assembly Dispenser board. I have water to the Pilot valve ( The valve in back of the frig ) I emptied the water in the reservoir in the door. But still, the pilot valve is not energized. Do I need to get a PCB board or can you tell me why I get no water?

Thanks
Bill
Neighborhood appliance

This is an oven/microwave combo. Oven works fine and microwave works good except for it will not run longer than 1 minute. At that point, in the oven control board screen it will give an error code of F3E2. The microwave board doesn’t display this code. The oven sensors check fine as well as the oven works great! Not sure what this could be causing this as all works well except for the 1 minute time issue. Set for 3 minutes will cut off completely at 2 minutes. Any time frame will do the same.you can also start the microwave back up instantly and it will run for 1 minute. Any help would be great!!!

The machine is not working properly. According to the customer. It worked fine for mr, however the lid lock didn’t lock during the wash cycle.

there was a power outage, then when power came back on. Refrigerator didn’t work and front display blank

Why the compressor is working all fans are working temperature set at 33 F for refrigerator -2 for freezer . The compressor sound working good and yet not cold. Please let me know email me or call me at 305-748-0512 please!

Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???

Can’t figure out what is going on with this refrigerators icemaker. I have changed the icemaker, and it still will not cylce. The optic sensor will come on for awhile then will go off after a bit, until I unplug the unit, then they will reset at that point. The water valve is good. I put in diagnostic mode and the optic sensor read as should, so I am not sure why this unit will not make ice. FYI all switches are good as well.

I removed the control module and replaced,the touchpad. The display no longer works but everything else,does. Did I leave,off a wire which I can’t find, or is something else going on.