We have a Bosch Dishwasher that goes straight to clean after starting. I won’t bore you with the parts that have been installed. Has anyone ran into this problem that can help?
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
Fills but does not drain goes through cycle except for drain
- Guest asked 6 years ago
- last active 6 years ago
Microwave turns on for 2 seconds and then turns off. History: I changed out a blown fuse about six months ago but did not know at the time I should have changed the monitor switch. Last time it was dead and now it just turns on for 2 seconds. Any ideas what I should be looking for? Model #HMB5050/01 FD 9007100017 FCC ID ACLAP7A01
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
Buttons will not respond, start then shuts off, will not fill.
- David Sutton asked 6 years ago
- last active 6 years ago
I need a new door seal for this model, anyone have time to do the lookup for me? Thanks.
- Harley Clark asked 9 years ago
- last active 9 years ago
disher are not getting clean, soap at bottom of tub.
- Harley Clark asked 6 years ago
- last active 6 years ago
It displays zeros instead of the time requested. we replaced the control board and it still same issue. Because it does not show time, it does not start.
- Guest asked 6 years ago
- last active 6 years ago
- Guest asked 8 years ago
- last active 8 years ago
This dishwasher was just re-installed after a kitchen remodel. I got called out because it wasn’t draining. I removed the knockout from the disposal the first time thinking that was the issue. Turns out it wasn’t, still having issues. This time I’m getting a bad pump but cannot find the part number anywhere. Somebody there able to look it up for me?
- James Buchanan asked 9 years ago
- last active 9 years ago
How do I test soap dispenser using diagnostic codes to activate solenoid.
Is there a video for Dissasembly of door and testing of part 00645208 to make sure the solenoid is working and the control board is sending correct voltage?
What is voltage used to activate solenoid.
Should I remove entire door?
Removing dispenser is tricky is there a better way?
- Guest asked 7 years ago
- last active 7 years ago
Error code 1006 on Thermador
- Guest asked 5 years ago
- last active 5 years ago
fast wash which is a 30 minute cycle goes down to zero and then it turns back on again and went to 15 mins cycle…. for the 15 mins cycle then goes through another wash cycle….so the 15 mins wash it went down to zero and everything drained and there is no water in it now so it works on the 15 min cycle and not the 30 mins cycle (wont turn off on 30 mins but shuts off on the 15 min cycle)….for the 30 mins has to shut off manually which then leaves water in the dishwasher
- Guest asked 6 years ago
- last active 6 years ago
The fuse blew to the microwave side its no power. The thermostats are tested and capacitor good. Suspect its transformer and high voltage fuse on transformer. Part list with diagram to would help not finding part numbers
- Guest asked 3 years ago
- last active 3 years ago
This unit overfilled due to no loop in drain line and started the drain fault cycle.
Now unit is completely dry and can’t get unit out of drain fault cycle. Have tried putting unit into diagnostics mode but will not go into diagnostics. Not familiar with Bosch DW. Any advise on what to do next. Can lift up float in bottom and hear the switch clicking closed and open. Thanks,
- Fred Abernethy asked 8 years ago
- last active 8 years ago
This unit flags the clogged drain error and the washer still has soap in it when there error is displayed. I thought it might be a faulty pump so I replaced it but the error still shows up. When the dial is set to drain it flushes the water in a hurry every time.
Thanks for anyones input,
- Hall Refrigeration asked 8 years ago
- last active 8 years ago
The dishwaher will not drain.
- Guest asked 6 years ago
- last active 6 years ago
Bosch dishwasher 5+ years old has worked fine. Now blowing circuit breaker at various points in cycle. I replaced power cord after observing cut taped over in cord and frayed wires inside. Cycle started normally, then breaker blew again after 30 min. What to do next?
- Fred Abernethy asked 5 years ago
- last active 5 years ago
Our Bosch dishwasher is about 4 years old, after you run a cycle there is a lot of water remaining in the bottom, I have checked the sump it is clear of obstructions and the impellor turns free, after the cycle if you lift the float on the base, in about 2 or three seconds the pump runs and will drain it if you keep holding the float, it takes about a minute.
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
Door latch buzzes 3 times and won’t unlock
No error code comes up
- Guest asked 7 years ago
- last active 7 years ago
Looked at above Bosch dishwashers, did not find wire diagram in either one. I thought they were stuck in a pocket in the base behind the toe plate. Not behind outer door panel, so anyplace else I should look?
Customer says it doesn’t clean and dishes are not hot like before. I did the following checks while it was washing. Heater circuit (R – W/R wires) had 120vac and 9 amps. NTC (O-O wires) was at 25.56k ohms and water was 95 degrees. Wash motor was pulsing, I am thinking the washer is trying to heat the water. Does anyone have a wire diagram / tech sheet for this model? Any suggestions on what to look for?
This unit has a timer, so I checked all wires on the timer. To ground, B, W/R, PU, GY, AND GY/B all had 120vac. GY/B had 8.86 amps at one point. I am guessing this is the heater circuit? A thermostat on top of the door inner panel (W – Y wires) was open.
Anyone with a wire diagram / tech sheet for this model? Any suggestions on what to look for?
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
Need a tech sheet for above model of Bosch fridge. Freezer is cooling fine but fridge is not cooling at all. Want too check readings at main board for different parts instead of just putting in a bunch of new parts. Steve
- Guest asked 8 years ago
- last active 8 years ago
I have an upcoming appointment for a dishwasher that the homeowner claims is not spraying as much water as before. Just in case it is not a clog in the spray arms I was just wondering how I would enter into the diagnostic mode. The homeowner claims she culd not read the serial number – sorry.
- Guest asked 7 years ago
- last active 7 years ago
I have a Bosch Ascenta dishwasher and the child lock is on and is preventing me from doing a load.. Have no idea how to turn it off as I just moved into this house and there is no instruction book
- David Sutton asked 5 years ago
- last active 5 years ago
I have a customer with a washer that will not stop beeping. The first time out I found a restricted fill line that would not let the unit fill and wash. Corrected that issue and units runs. Bosch will not talk to me as I am no longer an authorized anything. The customer and I have both determined that the controls work to the point you can raise the tone level and lower it to off. I did change the main brain, on advise from another servicer that said they solved a similar issue by changing the brain. Unit seemed to work okay, left the house and came home. As I walked in the door the customer called and advised the unit ran part of the way thru and started beeping. At last count she had it at 137. Has anyone any suggestions that will help me help her. Thanks.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago