1 vote
52 views

No power at all, already checked the fuse and it’s good.

0 votes
126 views

This is an Microwave/ Oven combo this unit has power and all functions are working except for the microwave is not producing heat. The microwave has lights and the turntable motor turns as it should, we are not sure what is causing these issues now.

0 votes
121 views

KITCHENAID MICROWAVE RAN DIAGNOSTICS ERROR F1 E5 SCREEN SAYS REPLACE MICROWAVE INVERTER. I REPLACED INVERTER AND MICROWAVE CONTINUES TO GIVE SAME ERROR CODE. I CHECKED SOME OTHER POSTS AND THEY INDICATED THAT HE APPLIANCE MANAGER IS THE CULPRIT. I REPLACED THE APPLIANCE MANAGER DIAGNOSTICS SAYS STILL SAME ISSUE F1 E5 CAN YOU TELL ME WHERE TO GO FROM HERE. I TRIED TO RESET ERROR BY GOING INTO DIAGNOSTICS OFF OFF START THEN 6 THEN 6 AGAIN THEN PUSH START AND THAT IS SUPPOSED TO RESET BUT ONLY BEEPS.
WHAT OTHER CHECKS CAN I DO.

0 votes
152 views

FAN RUNS EVEN WHEN MICROWAVE IS OFF AND CODE 161. WHAT COULD IT BE ?

  • rdappl asked 7 months ago
  • last active 7 months ago
0 votes
131 views

doesn’t turn on to cook but the timer stills counts down like its cooking.

1 vote
199 views

This is an oven/microwave combo. Oven works fine and microwave works good except for it will not run longer than 1 minute. At that point, in the oven control board screen it will give an error code of F3E2. The microwave board doesn’t display this code. The oven sensors check fine as well as the oven works great! Not sure what this could be causing this as all works well except for the 1 minute time issue. Set for 3 minutes will cut off completely at 2 minutes. Any time frame will do the same.you can also start the microwave back up instantly and it will run for 1 minute. Any help would be great!!!

0 votes
114 views

My GE MICROWAVE bejv177zla suddenly stopped working. I’ve replaced the fuse and used electronic cleaner spray on the door locks the clock is out Could it be the thermal fuse on the magnetron?

0 votes
137 views

When opening the door on the microwave when it is still running it flips the breaker. A friend told us last night that should not be happening. Solutions?

0 votes
155 views

One of the shelf supports on my Amanda microwave partially melted. I found and purchased a replacement. How do I remove the old support. Can I pry it off with a screw driver? Will this damage the interior. The shelf support part number is 2080030.

1 vote
175 views
  • Pancakes asked 8 months ago
  • last active 8 months ago
0 votes
839 views

My Samsung microwave is showing an e83 filter code how do I fix it?

0 votes
192 views

Error code 1006 on Thermador

  • jjwheels01 asked 8 months ago
  • last active 8 months ago
0 votes
186 views
0 votes
157 views

I need to remove and replace the control panel on my GE microwave model JVM6175EF1ES. I have the part

0 votes
220 views

Hi my kitchenaid microwave went completely dead on me after the door mechanism got stuck. I was able to release it no problem and the door opens and closes perfectly but the unit is dead as can be. Checked the breaker and it’s A-Ok.

0 votes
162 views

not heating

0 votes
150 views

My microwave can not be used because of a code on the screen that says F9Q

0 votes
144 views

My Microwave is in lock mode. How do I unlock it?
GE model number JNM7196SK1SS
manufactured December 2016

0 votes
184 views

My microwave just stopped working in the middle of a heating cycle as I was opening the door. No power, no lights

0 votes
175 views
0 votes
201 views

Hi,
The microwave blowing fuse, I was testing the switches I found the normally closed one is no good, I changed the switch.
The microwave worked perfectly at that time, now when opened the door again, the fuse blowed up again. Now I need help on what I should do and what is the problem.
Thank you.

  • Pkjuste asked 10 months ago
  • last active 10 months ago
0 votes
162 views

I have a built in GE microwave and all the keys and settings work on control panel but when you push start it hums but does not come on.

0 votes
137 views

My KitchenAid microwave convection oven turns on, lights up but carousel does not turn and food doesn’t cook. was working fine until i used what i thought was the timer for 60 minutes – turned out it was on for that length of time.

0 votes
169 views

I inadvertently put the microwave on for an hour thinking it was on the timer. It is dead now. Any ideas?

1 vote
171 views

I Had a OL reading on a Cavity thermostat. Tech sheet said it was a single pole thermostat and that the contacts close at 158 degrees Fahrenheit. Now i thought this was a normally open thermostat then? totally confused me? Can you ellaborate with this. is that when they close after being heated up, or is this normally open? this is ona microwave btw which i thought would break the circuit.

  • Manlmich3 asked 10 months ago
  • last active 10 months ago
0 votes
160 views

No power on microwave. Found breaker tripped and it worked for a short time but now it’s out again and breaker is good. Model:JVM1740SP2SS

0 votes
167 views

With the door open, the turntable runs. No heating. No magnetron. It also pauses now and then. I’m certain the control board is bad. The model is the one you mentioned above. I have priced a board. I will change it out. I have found I can buy either the control board itself or the entire assy.Question: is there any stored electrical charge? Capacitor, ect ect? Do I ground the board during change out?

0 votes
170 views

Need to get handle off microwave door.

0 votes
126 views

Hi My microwave is working except for the sensor options. When I press “potatoes” or “sensor reheat” and “start” it flashes ERROR. I tried resetting via fuse; no luck. Time for a new microwave?

  • Don Kopecky asked 10 months ago
  • last active 10 months ago
Showing 1 - 30 of 210 results