0 votes
3k views

Door handle loose how do I check or tighten hardware inside door

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I just replaced the thermostat and found the evap fan motor cycling on and off about every 2-3 seconds. Is this a bad motor or board or ?
Why is it cycling? I have never come across a cycling motor before. It either worked or it didn’t. How can I check to determine IF it is a failing motor?
Thank you

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Clothing gets stuck, tub moves around a lot, bad smell, standing water.

0 votes
2k views

Leaking water.

0 votes
2k views

I’m trying to replace the main power board. replaced old board but the fridge dose not start up, no lights nothing, controls dead. I also replace the thermistor
Reinstalled old board fridge started up, lights working, controls working.
Installed another new board. nothing.
Fridge is also missing the tech sheet.
Initial problem, Items freezing items in fresh food section,
Thanks for your help

  • rfcorral asked 5 years ago
  • last active 5 years ago
0 votes
834 views

My Electrolux washer is off balance and shakes around when in use.

0 votes
3k views

Fridgidaire (electrolux) affinity.
Error E66

Hi there and thanks for making the youtube video. I have the dryer open and the drum out. I have a multimeter but to be honest it is one of those tools I don’t really know how to use. What setting do I put it on to test the doohickeys? What am I looking for on the multimeter to determine if its bad or good?
After writing the first question on the youtube comment section I set it it the 20ohms and get a reading of 1.1 and 1.4.
Also when I took the dryer apart there was a lot of lint, coins and some other misc debris in the bottom of the dryer. Is this normal or might I have a leak somewhere?

  • stephen asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Can Reverse osmosis filters be used on ice makers ?

0 votes
2k views

Has error code on display , do you have service sheet ? Thanks

0 votes
2k views

My washer will not spin. Any suggestions?

0 votes
2k views

My Electrolux Refrigerator drawer will not open.

0 votes
2k views

THE EVAP COIL HAD A LEAK WHICH I REPAIRED. I RECHARGED THE SYSTEM. I HAVE 0 PSI AT THE PROCESS STUB AND ABOUT A 70 DEGREE DROP ACROSS THE CONDENSING COIL. THE UNIT ISN’T COOLING PROPERLY STILL. THE TEMP DROP ACROSS THE COIL HAS ME STUMPED AS SEEMS TO ME THAT IT SHOULD BE WORKING. ANY THOUGHTS? TX

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Evap fan motor cycles on and off It started out cycling about every 2-3 seconds. After a couple of minutes it cycles to the point that it continues to turn, but not a full speed.
1. What causes this?
2. If it is the board, how do I test it to determine that it is the board?
3. If it is a bad motor (?) how do I test this?

I’ve never tested a fridge board or run it through a diagnostic test.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

E40 error, E47 error, washer starts then shuts down.

0 votes
2k views

No heat.

0 votes
1k views

My washer is displaying an 84 error code.

0 votes
3k views
  • derrick asked 9 years ago
  • last active 9 years ago
0 votes
2k views

Electrolux Refrigerator. Nothing against Electrolux don’t know a lot about them we do mainly high-end /built in work.
Says in the morning he gets a slushy from his through the door ice dispenser.
Besides the obvious flap/dispenser door not closing, warm air intrusion etc. any brand specific idiosyncrasies / service bulletins /kits to be aware of with this particular unit and reported problem.

0 votes
2k views

My electrolux refrigerator is not making ice.

0 votes
2k views

Ice dispenser not working properly.

0 votes
2k views

DDO Error, Fabric Softener will not dispense, drawer will not drain, Clothes are not getting clean.

0 votes
2k views

Not powering on.

0 votes
1k views

FRESH FOOD SECTION NO ICE PRODUCTION
FREEZER SECTION LOW ICE PRODUCTION CHECK WATER VALVE ELECTRICALL OK BUT THE WATER COMING IN TO THE WATER VALVE BELOW 30 PSI WILL THAT CAUSE THE ICE MAKERS TO NOT PRODUCE ICE OR LOW ICE PRODUCTION OF ICE I DON’T BELIEVE THE ICE MAKER CAN BOTH BE BAD ANY SUGGESTIONS ON WHAT TO CHECK

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
882 views

The water will not drain out of the washer.

0 votes
2k views

the power failure alarm was on. could not turn it off the alarm on the door control because nothing was working. i unpluged and pluged it now the refrigerator comes on for couple second and goes off and does not stay on. it goes off an on what do i need to change to fix this problem

  • norman asked 9 years ago
  • last active 9 years ago
0 votes
2k views

This one has me stumped. Machine is giving E21 “Water not pumping out fast enough” error. Starts by pumping out at a trickle and occasionally will “kick in” to full flow. Pump sounds like its sucking air/air locked. Will drain properly every 4th or 5th attempt. Removed and checked all hoses, found all to be clear. Removed tub-to-pump boot and looked up with mirror to bottom of tub and could see the inner tub with no obstructions. Tried running pump directly with test cord to rule out low current from main board and tried new pump with same results. Any Electrolux experts out there with suggestions? Greatly appreciate any help

Showing 31 - 60 of 202 results