Brand: Frigidaire

I HAVE NO POWER TO THE WATER CONTROLS ON THE DOOR AND THE EVAPERATOR FAN IS NOT WORKING. REFRIGERATOR BEEPS EVERY FEW MINUTES

When I push the start button u hear the motor trying to start and then goes dead.
I changed the belt worked for one cycle and then stoped

The temperature in the freezer is 49. The refrigerator is 59. The temperatures are set at -6 and 33. I unplugged the main board and plugged it back in and the compressor and condenser fan started but quit later. Have you seen this before and is it the main board?

I need a service manual for this model also.

THE CUSTOMER IS TELLING ME THAT THERE IS HEAT, BUT THE DRYING IS TAKING TOO LONG. I DID NOT GO TO SEE IT YET, COULD SOMEONE WALK ME THROUGH THE DIAGNOSIS? THANK, TODD FROM NY.

So it takes a long time for it to preheat the igniter is fine after some time the oven shuts off but the preheat light remains on

Wiring diagram needed for Frigidaire dual range Model# PLCF489ACB
I am having the board rebuilt by CoreCentric and would like to have the wiring diagram to make sure everything is wired correctly. I am not the first to work on this. Any help is greatly appreciated.I would try looking for a video at ApplianceVideo.com. Just type in your symptom and look for a free video.

My Frigidaire refrigerator is not dispensing ice.

My Frigidaire refrigerator is not getting water to the ice maker.

My Frigidaire dryer is displaying a “LOC” error code and wont do anything else.

Hi, I have a Frigidaire refrigerator not making Ice. I changed the ice maker and still not making Ice, water pressure is Ok and filter recently changed. I noticed I couldn’t turn the euger motor by hand. I’ll appreciated if you could help me.

Everything else works but there’s no water coming into the machine. I have checked the water hose and there is water in the line I have tested the water inlet valve for continuity I’m getting 0.808 ohms of resistance does that mean the water inlet valve is faulty and if it is good what else can be the problem thank you

The customer had the oven set to 500 degrees and forgot about it and left it for several hours. The next time and following times the oven does not heat up to where it is supposed to no matter how long the oven is on. If the customer wants it at 300 degrees, then she has to set it to 375 for the temperature to be 300. She always needs to set it 75 degrees above the temperature. What is causing the oven temperature to be low?

I have a Frigidaire Dishwasher that is not working

I need a service manual to test this unit. I’ve never seen this one before. Is there a way to test the temperature in the ice room? If it is turned off should the temperature be in the 40’s? I ran the checks in the tech sheet and it does move and the fill valve works but I don’t understand the principle of operation. I need to know how to disassemble it.

When I arrived the freezer was frosted up. I put it in the service mode in defrost and the heater did not come on. I found the defrost thermostat was open. I removed it and temporally bypassed it and still no voltage , nothing coming to the heater. is this a main board issue plus the DFTS? I need a service manuel. The tech sheet does not give much information.

Ran through diagnostic mode it flashed the lights indicating it was the main board malfunctioning. Replaced main board. Still won’t complete the cycle. Could it be the board below the drum? Ran fine when I left the appointment. But sometimes it took longer then usual to drain. When I ran through diagnostic mode. Tested it 4 times before I left.

My question is what would cause the F30 error code to come up I did a preliminary search and found it had something to do with the oven probe or the main control board I tested the resistance of the oven probe and had 1.097K which looks to be correct . The manuals that I downloaded off the Frigidaire site did not have anything corresponding or any information on error codes .
I would like to confirm that the main control board needs to be replaced after checking the probe if that is what the F30 error code means

It does display system diagnostics. Numbers 2 thru 47 but will not show 52c- 63c per the tech sheet instructions.

The ice maker produces plenty of ice, but after about only about 4 days the unused cubes form a solid block in the bin that must be removed and melted in the sink. Why is this happening? My refrigerator is a model FRT21FD3A

If no video, anything you may have to help me figure out how to break down this dryer would be greatly appreciated.