Brand: Frigidaire

The customer hasn’t used their ice maker in the ice room (fresh food section) in a couple years because it stopped making ice. Today I was there, all around the ice maker mold and motor it was covered in heavy frost. I got that out of the way. There were cubes on the “fingers” of the evaporator. I have never worked on this type of ice maker before and need some guidance on how to trouble shoot it
The mold was below the fingers (not sure what they’re called).
Can this ice maker be forced cycled?
Do you have a video on how to take it out and inspect it?
I understand there’s a fan motor in behind it, I did not hear it running.
Any help would be greatly appreciated.
Thanks,

evaporator motor was replaced the adc electronic board was replaced and the damper assembly was replaced and frigde is still not getting cold it’s cool, not cold enough
please help

So I changed the coils and the igniter and the senser.
The falme still will go on for 5 to ten seconds and then go off.
And will repeat about 1 minute later
I have have taken the vent off of the back and no difference

Dispenser Problem/ Repost from yesterday
Refrigerator Frigidaire
Unexpectantly the dispenser hatch rapidly opens and closes and if the dispenser is set to water it comes out each time the dispenser opens and closes. What is the cause of this problem? The customer said she googled it and found it is a common compalint. Is this so?

The main problem is NOT trickling water but that whenever the dispenser WANT’S TO; ALL ON IT’S OWN ACCORD it , at any time opens and closes its hatch over and over for several second’s then stops. Without ryme or reason. Wouldn’t this be a circuit board issue? and call for replacing it?

I replaced the dispenser module first and that didn’t help at all. Then I reinstalled the old one and replaced the main control board, and that seemed to fix it then after three trouble free days then it started again. Now what do I do? Is the display a possible cause? It is almost $500.00. Any other ways to try to determine what is the problem?

This dispenser module you sent is the one I replaced. Sorry for the confustion. Any other suggestions

I was getting an error message sy… and I was told to change the switch board under the front of the unit.
I changed it once it didn’t power up so I thought it was faulty.
so I changed it out for a new one.. I hot the new one and I have the same issue. it just will not power up

so the washer will not go on.
i did see that when i unplugged it and put it back on the lights went on for a sec

so the fridge seems to be working fine.
however the freezer is not freezing.
i took off the back panel to check the evaporator coils and there is only a bit of frost on the top part of the coils.
how may i correct this issue?
thanks

never worked on this model. 3 months old, cust complaint dishes still dirty, started unit thru wash cycle, jets on top and bottom wash arms are obviously clogged, tried taking them apart to clean with no luck, need service manual or advice on how to disassemble and repair this unit, model # lgid2475qf3a. also noted that top spray arm does not rotate even though water is shooting from arm, Its odd to me that jets are soooo clogged up for such a new machine. I have no information on this model because it is too new.

Everything else works but there’s no water coming into the machine. I have checked the water hose and there is water in the line I have tested the water inlet valve for continuity I’m getting 0.808 ohms of resistance does that mean the water inlet valve is faulty and if it is good what else can be the problem thank you

Excessive steam coming through vent at top of door, accumulating and dripping on floor.
Anyone seen this? Ni filter or damper door, just a duct that lets steam out.

Looks like I’ll need information on the electronic control for this, will confirm for sure when I get there but want to be able to have a handle on the parts needed before I walk through the door.

Thought it just wasn’t heating up, but it actually wasn’t running at all. Looks like a busted door switch. Do you guys carry it?

My Frigidaire refrigerator is not getting water to the ice maker.

The ice maker in my Frigidaire refrigerator is freezing up and will not dispense ice any suggestions?

We have aproblem with this unit. it doesn’t make any ice . We found for sure the one of inlet valve coils is open ,
but the same time we can hear some strange knocking sound from the ice maker .
We never worked on this kind of ice maker before ,it looks kind of strange one for us
Any help would really appreciate

so the compressor is dead.
can you please tell me how i change it?
maybe a video instructions

the unit will go on a 44 minute cycle.
and it’s at 43 for over ten minutes.
I cleaned out the drain line.
I hear some noise from the motor but it will not turn .( I can turn it by hand ).
and every few minutes I hear the water go in for about 1 second.

I have a Frigidaire Dishwasher that is not working

I need a service manual to test this unit. I’ve never seen this one before. Is there a way to test the temperature in the ice room? If it is turned off should the temperature be in the 40’s? I ran the checks in the tech sheet and it does move and the fill valve works but I don’t understand the principle of operation. I need to know how to disassemble it.

When I arrived the freezer was frosted up. I put it in the service mode in defrost and the heater did not come on. I found the defrost thermostat was open. I removed it and temporally bypassed it and still no voltage , nothing coming to the heater. is this a main board issue plus the DFTS? I need a service manuel. The tech sheet does not give much information.

Ran through diagnostic mode it flashed the lights indicating it was the main board malfunctioning. Replaced main board. Still won’t complete the cycle. Could it be the board below the drum? Ran fine when I left the appointment. But sometimes it took longer then usual to drain. When I ran through diagnostic mode. Tested it 4 times before I left.