Brand: GE (General Electric)

Need help diagnosing unit. Also is there a video on how to take off the top panel off to see the inside. Please help

Gentlemen, I have not checked this unit yet the complaint is a no drain issue. Do you have any service information available that you could share with me on this Dishwasher. It would be a great help and greatly appreciated. Any service bulletin or service advise is always appreciated as well. Thank you for your help.

The controls on my cooktop are not working.

So I’ve replaced the tub bearing and tranny due to a leak, reassembled and tests good, washer 7 loads and it through a main computer replace error. Replaced the main control and door lock and it washed 7 loads and it wont wash again. The on, wash and lid lock light are on and it wont do anything. Any ideas?

My dishwasher is leaking water.

The only thing that works in the fridge is the light. Nothing else comes on.

THE REF FAN HAS NO POWER AND DAMPER DOOR IS NOT OPENING.

I’M THINKING BOARD ISSUE BUT NEED TO KNOW WHERE THE TEST POINTS ARE LOCATED

TX

My dishwasher is not mounted in the wall properly.

Ran through diagnostic mode all major components seem to check out and service manual with that unit does not have a F 36 code. The unit seems to come on normally but as soon as you hit a function it flashes the Error and shuts off. Can you guys give me an input not just the manual it doesn’t seem to have an answere.

I have a GE SPACEMAKER stackable washer/dryer. Customer complained that the washer knob broke off and that the washer is not working. When I arrived I noticed the knob from the washer side was off the potentiometer aperture handle (timer knob) resting on the washer. I tested the dryer and the dryer appeared to be working fine. I tried to start the washer to test it by turning the timer knob (which had fell off of the control panel frame bracket) and pressing start button. Not only did the washer not show any sign of life by not starting, but I tried turning the knob on the timer without the knob attached and I could not hear any “click” coming from inside the timer indicating that it was advancing to the next stage of the washing cycle.
I removed the control panel cover and noticed the timer slid out of place in its socket when it was supposed to be securely fastened to the front panel. The knob was turning but the timer was not clicking as it advanced. I tried to unplug the connector OF THE TIMER from the wires but coud not notice any discrepencies visually. Should the wires have been checked ?? continuity ? voltage ? Could I have a bad timer ? If the dryer works fine and the power is getting to the dryer and stopping when it gets to the washer could the timer be preventing this ?
Timer part # 131758600 (WRITTEN ON TIMER ITSELF)
GE Spacemaker Washer Dryer combo WSM2700DAWWW

The door on my dishwasher just slams shut.

when I turn on the stove it show me error f 7 and f 9. it don’t let me do nothing. It don’t let me press bake. when i clear those number it come back again. I can not used the oven. I don’t have problem with the top. what i need to do? do i need to reset?

My refrigerator is always running.

have foloower instructions to get into service mode. it mentions: delay wash and extra rinse button. see neither. have rinse with extra rinse option ?

GE profile washer without agitator will not agitate

This ge fridge is showing temps different than what’s set. The big thing is the temps shown vary greatly with the set temps. With thermometers placed in the fridge and freezer they show good temperatures inline with the set temps. The fridge has never got over temp.

The light on my GE dryer is not working.

Hello
Older side by side GE refrigerator – complaint is that ice clogs the chute – when calling for ice it seems as if the ice comes out of auger bucket too soon and doesn’t allow the door to open in time – I replaced the time module delay (WR55X129) in the hopes that that was the culprit – almost a month later and the customer is calling back with the same complaint. Ice size seems appropriate and dispenser door seems to open and closer properly. Ice cubes are proper thickness and good water supply to ice maker . Thanks for any help

I am looking for a tech sheet for this dishwasher. Initial diagnostic mode we determined the door latch and strike should be replaced. The homeowner previously replaced the wire harness and main PCB board. After replacing latch the machine won’t start. When go into diagnostic all lights blink even when door is shut. Will not enter service mode at all. Hopefully you can send a tech sheet for this model please

Does this unit have a heat exchanger?

My technician said he needs this part due to a Freon restriction. We are not finding a picture on the parts diagram.

My tech said its a capillary tube running from the evaporator that is likely restricted. He was working on a sealed system repair, replacing the compressor and evaporator today.

Please let me know the part number that would be needed.

Wall mount GE dryer:When press start bottom starts but doesn’t continue running.is it the motore?

The ice maker is dead, the reset button does nothing. Will the im harvest if the ice room thermister is bad? Does the wr23x10580 interchange with the wr55x10025? Do they share the same resistance ratings at certain tempuratures? Is there anything I didn’t check?