Brand: KitchenAid

so when the unit is plugged in it clicks the entire time.
i want to changed the spark module . however i would like to know if you can please share some tips on how to do it
thanks

The touchpad on my KitchenAid dishwasher is unresponsive

Display shows TEMP SENSOR

I replaced the W10428901 control board an I am getting PE 000 code. I do not know the proper button to push to set the code. the code on the model tag is 13.

I have a kitchen aide fridge that runs but the freezer fan will not run and it keeps freezing up. I have not found a way to just test the fan while in diagnostics mode. How can I run a test to check to see if I am getting voltage to the fan or if I am having a problem that coincides with the control board.

Cant seem to have this ice maker working replaced all common parts. Any suggestions.? Thanks

Door just falls open.

Error F2 E1, Error F2 E2 Displayed, Cannot control oven, buttons will not respond.

PANEL TURNS ON BY ITSELF AND CHANGES SETTINGS, THE MICROWAVE ITSELF DOESN’T TURN ON, BUT THE PANEL JUST DOES RANDOM THINGS. ANY IDEAS?

Some of the buttons on the touchpad of my dishwasher are not responding.

Our ice maker in the bottom freezer does not work. We also hear a crackling/clicking sound. We vacuumed the bottom really well but still no luck.

Above items not working. Are they connected. Circuit wise? Please help with troubleshooting. Put it into diagnostic mode and it shows up with replace filter sign on first step. When I advance it to next step, it says order filter. When I check filter, it says it’s hundred percent. It’s been a big mystery. Thank you.

refrigerator makes a noise in the freezer and it has a lot of ice in the back

My dishwasher seems like its not getting power to it.

My Kitchen Aid refrigerator is not cooling properly.

Normal button blinks and the other buttons are inoperable. The dishwasher does not work.

I’ve replaced a non working evap fan and it cools but not to the proper temp programmed.
Kitchenaid ksc24c8yy02

My kitchenaid washer is leaking and has a broken lid switch.

My Kitchenaid refrigerator is getting water to it but not making ice.

Customer says that over 7 techs already visited him to try to solve freezer still warm issue.
There is no frost build up near evaporator coil. Heater, thermostat and fan inside freezer work.
customer says previous techs suspected a leak or sealed system failure. They changed compressor, 3 way valve, control board in freezer and fresh food section fridge. But freezer still warm. If the compressor is new could they have missed the start relay before the compressor ? Does it always have to “click” before you determine it is bad ?

The dishwasher blue light will come on like it is going to start the cycle. I hear no noise and then the blue light goes off. when I open it, the cancel, drain light is on.

IT APPEARS TO ME THAT WHEN THE FRESH FOOD DOOR IS CLOSED FOR A WHILE, THE TEMP CONTROLS TURN OFF. WHEN THE DOOR IS OPENED, I PRESS THE ON BUTTON AND EVERYTHING COMES BACK ON. SO IT APPEARS TO ME THAT IT’S TURNING ITSELF OFF. ANY THOUGHTS ON A CAUSE WOULD BE APPRECIATED.

TX

My dishwasher door falls freely and does not latch

Refrigerator evaporator freezing and not defrosting properly any suggestions

WE HAVE A MICROWAVE/WALL OVEN COMBO WITH A F6 E8 CODE. THAT CODE IS FOR THE MICROWAVE APPLIANCE MANAGER (iE CONTROL BOARD). CHECKED THE WIRE HARNESS TO THE DISPLAY BOARD, WHICH IS OK AND THEN REPLACED THE APPLIANCE MANAGER, STILL GET THE SAME CODE. THE ONLY OTHER THING LEFT IS THE MICROWAVE DISPLAY BOARD, WHICH IS NOT VERY COMMON AND TWICE AS EXPENSIVE. SEEING IF THERE ARE ANY SERVICE UPDATES FOR THIS PROBLEM.

THANKS