I’ve replaced a non working evap fan and it cools but not to the proper temp programmed.
Kitchenaid ksc24c8yy02
- Guest asked 10 years ago
- last active 10 years ago
Looks like the ice maker is shot, any one there have the part information readily available?
- David Sutton asked 10 years ago
- last active 10 years ago
I am working on a 4 door kitchenaid refrigerator that has icemaker in the celling in refrigerator side how do you get it out , dose anybody have a service manual to share whit me MOD#KFIS29PBMS02 and SER#K33307442 help is very appreciated
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
I have a Kitchen Aid wall oven, electric heat. Model # KEBS107DAL4 – gives fault code:
F3 – E2 ( Oven too hot Replace oven temperature sensor)
This fault code only when self-cleaning. Bake and Broil works fine.
Wouldn’t the sensor fail for baking as well? Thanks in advance for any help.
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
Have a kitchenaid wall oven. Model KEBS107SSS04
Error code says to replace the ( UI ), I assume this means USER INTERFACE.
touch pad and pc display board. Neither are identified as a UI and both are costly.
- Don Kopecky asked 10 years ago
- last active 10 years ago
We have a customer with a Model# KURG24RWBS Serial# EK31901299 that has a defective defrost bimetal that is part of the wiring harness part number W10299078. The fine Whirlpool corporation has no eta on this part as they currently have no vendor we believe the refrigerator may have been made by panasonic. The unit is only a year and a half old and Whirlpool is not willing to help the customer in any way. There are no temperature ratings on the bimetal at all just some markings PW-5M2R 4033 R4 which if I play around on google appears it may have been made by SENASYS. Any help would be greatly appreciated
- Hall Refrigeration asked 10 years ago
- last active 10 years ago
Replaced door lock after power on .after 30 seconds display F1 what F1 means
- Guest asked 10 years ago
- last active 10 years ago
was told everything is running but not getting cold on fridge or freezer
- Guest asked 10 years ago
- last active 10 years ago
f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc
- Guest asked 10 years ago
- last active 10 years ago
can you provide me a brief description on how to remove the top rack on a KUDE404DSS dishwasher? Or possibly a video showing this process? thanks in advance
- Guest asked 10 years ago
- last active 10 years ago
KitchenAid dishwasher model KUDS30IXBL8 do you have parts list ?
- Guest asked 11 years ago
- last active 11 years ago
We have a kitchenAid refrigerator that previous company replaced ice maker and ice maker optics, we were called out, found that water valve to ice maker was bad. replaced the valve and ice maker still not harvesting, I checked power to the ice maker, holding the interlock switch and no power, went behind the kick plate at quick disconnect no power there either… There is no tech data with refrigerator does anyone have a tech sheet or advise on how to proceed. Thanks.
- AV Repair Help asked 11 years ago
- last active 11 years ago
We have a kitchenaid refrigerator that previous company replaced ice maker and ice maker optics, we were called out, found that water valve to ice maker was bad. replaced the valve and ice mKSC24C8EYY01aker still not harvesting, I checked power to the ice maker, holding the interlock switch and no power, went behind the kick plate at quick disconnect no power there either… There is no tech data with refrig, does anyone have a tech sheet or advise on how to proceed. Thanks.
- Blake, Ace Appliance asked 11 years ago
- last active 11 years ago
I am going to ask this question again – I think that maybe I am not sure how to use the site – because I am not sure how to respond to the answer that Matt provided to me. The answer was not helpful because as I indicated I had already turned the power off to the dishwasher and that did not work.
Hi Mat The clean light flashes 4 times, stops for a bit and then flashes 4 times again continuously (the manual identifies this as an error code. I did unplug (power off) the unit and the problem was not corrected. I also sequenced through pushing the High Temp. Scrub and Heated Dry buttons several times as was identified online as a reset, but this did not work either. Is there another way to reset this model?
- Phyllis asked 11 years ago
- last active 11 years ago
- Phyllis asked 11 years ago
- last active 11 years ago
My door cables broke so I replaced them but the door squeaks like crazy any time I open it.
- Jason asked 11 years ago
- last active 11 years ago
- tracy asked 11 years ago
- last active 11 years ago
It goes through every cycle but the one we need, the wash!
- Sandra asked 11 years ago
- last active 11 years ago
ok. so I goo to repair videos.type in the above model #. click on tech sheet and it won’t give it to me. what am I doing wrong?
- Guest asked 11 years ago
- last active 11 years ago
hello
I have a kitchenaid dishwasher that starts to fill and stops before it reaches the float. the float moves freely and the float switch itself is good and electically works
any idea where to go next
thanks
james
- james asked 11 years ago
- last active 11 years ago
my husband says that he checked the igniter and it ohm’s out as being fine. He says it seems like the “spark isn’t reaching or big enough to ignite the burner.” Does anyone there know what could be happening here?
- anna asked 11 years ago
- last active 11 years ago
It seems that the only part number I see coming up for a p-trap drain kit is “W10619951”. In the video, it says there is a different kit for a fridge with 30″ doors, and ones with 33″-36″ doors. How do I know which part to get? I cannot find any place that clearly states which part number is for which size doors. Any help is appreciated. Thanks.
- Scott Thomson asked 11 years ago
- last active 11 years ago
Ice builds up on the rear of the bottom freezer section. It starts in the rear and eventually overflows to the bottom of the freezer section. I unplugged the unit and removed all the ice. About a week after removing the ice its starting to form again on the rear of the bottom freezer section. The ice maker is working and the temperatures appear to be correct in both sections.
- Lee asked 11 years ago
- last active 11 years ago
What can I do to change that? Or is it not possible? Just doesn’t seem to be the same and I’m not sure if it’s a good thing.
- Victoria Cochrane asked 11 years ago
- last active 11 years ago
How do we replace the two tracks that hold the upper rack? Is there a video that shows this? Ours does not have visible screws. Please advise. If you have a video, we would definitely subscribe to watch that video.
- Vicki Feinn asked 11 years ago
- last active 11 years ago
The bottom drawer is not cooling and top drawer freeze up on back wall?
- dan asked 11 years ago
- last active 11 years ago
This dishwasher we have seems to only be cleaning the bottom rack, the top has a lot of leftover stuff left on the dishes. I checked hot water coming in, and even cleaned the spinners out from another video I saw on here. Now what?
- John Knox asked 11 years ago
- last active 11 years ago
Dishwasher won’t start. Panel lights work. I press (Normal Wash), (Heat Dry) and (Start/Resume).
1) I can hear water softly running.
2) After a minute or so, I hear a 1 second long buzz that repeats every 5 seconds for a half a minute or so.
3) Then the cancel/drain light comes on solid. And, water is draining into the garbage disposal.
4) After 30 seconds or so, all the lights go out.
I reset everything by shutting off the circuit breaker. No change.
I think maybe the Float mechanism or switch is bad, so I remove the float and everything is very clean and free. I remove the switch and check it with a meter and it is fine.
So, what do I do now? Could it be anything else other than the control board?
- Carl Johnson asked 11 years ago
- last active 11 years ago
Our dishwasher hasn’t been very effective, and I thought it was a bad chopper assembly, so I changed that out, but it’s still not working as well as I’d like. What else can I check?
- Steve Murry asked 11 years ago
- last active 11 years ago
I have this gass stove , kitchenAid Model # KGRI801PBS00.
Costumer complaint: make short circuit , tripeed braker (or blow out braker) at braker box , then He restore power and blower motor kept running all the time ( non stop).
I take off the touch panel with the control box behind the touch panel and restore power blower fan motor kept running , so, I hit with my screw driver the relay board , the one is located behind the surface and get the motor stop .
But when , I put back the touch pad with the control is at back the touch panel and press the bake , the braker at braker box when off again (braker tripped).
another interesting question that I have is: I take away the cables going to the motor and check those cables for ground it was grounded , when the plug is inserted in the wall outlet, but if , I take away the plug from the wall outlet , now is not grounded is that ok?.
Now I , think I have problems with one of the board ,but I don’t know , which control board or even if the touch panel .
How I will determine or probe each one of this control or touch panel. thank for your help, wating for your answer, my email address is : armandoappliances@gmail.com , or also I have this other one : armgua@gmail.com. I am fan of yours wabesite and also I was refered to you, by marcone appliance which , we have accesd I belive as a premium till December 31.
- Guest asked 11 years ago
- last active 11 years ago