Brand: Maytag

Customer complaint is that it’s been throwing unbalanced errors. They will go on to readjust load but that does not help. All they can do at the point is drain the water.

Looking for any suggestions

I replace control board wpw10284942 and oven sensor. i was thinking of replacing wp74008369 board because the power goes from there i think.

The ice maker runs continuously and doesn’t fill. The diagnostic test indicate that the heater is on while it is running and the relay says it goes on and off when in diagnostics. I need a service manual. Also the original complaint was that ice was clumping together. When I removed the ice maker it had three cubes jammed in it. I removed them and reinstalled it and then it only made three cubes and that was it and the ice maker just kept running. If I run it in the diagnostics mode and run the ice maker shouldn’t it fill at the appropriate point in the cycle?

cust. has code problem fleshes either HF or FH cust. cannot tell

This unit is not cooling​ as well as the controls are not responding correctly. When you push the freezer temp buttons it will open and close the dispenser door.when you push the dispenser it will sound the alarm and all the LEDs lite. When any other buttons are pushed all the LEDs lite as well.

the oven will heat up and then go off after some time and the bake light will blink. I changed the control board and it didn’t helpll

Not washing clothes?

Please send diagnotics sheet so I can test machines parts in unit.

Looked online and technical manual both say check wiring from door latch to CCU or needs new latch. I tried a new door latch still error won’t even lock or start. Checked CCU board for burns looks good, checked wires for continuity good..
Could it just be needing a new CCU AND will I have to program it to take $2 dollars again for a wash with the new board or is that a separate computer inside the coin slot thing? Please keep the answer simple brain dead after this one.

I have a maytag neptune was that will not power on. I know the face board is good be cause I tested it on another exact maytag neptune

I have an apartment building full of these machines. Today I had a machine that the door is locked and will not release. Machine works fine except for the fact that you can’t put any clothes in! It will not release, per manual, in the time or anytime powering unit down to let the latch cool. Does anyone have a way to open the door to replace the latch ?

looking for which pins to check on board to see if ice maker is receiving voltage and signial from board

My Maytag top load washer is leaking. Seems to be occurring during drain cycle. I removed back cover and attached to drain hose is a smaller clear rubber hose, 8572540 FSP. The clear hose has a deep groove worn into it, assuming caused by vibration from rod it is attached to. Looks like this is where water is coming from. Is that possible? If this is the problem, what is name and part # for this hose, or can I use any clear tubing of the same size.

I have cleaned both hose’s.
I opened the inside and checked for a bent hose it looks good.
but I keep getting the LF regardless of what water temperature

nmbwholesale20124 days ago flag
(Lean washer back and turn transmission pulley in the spin direction (counter clockwise) and check for proper disengagement of brake. If brake is dragging add shim for proper spacing. Note: See service manual for proper procedure)

**THIS IS PASTED FROM ONE OF THE ABOVE DOCS.*** THANKS FOR THE QUICK RESPONSE. I’M LOOKING FOR THIS SERVICE MANUAL, CAN YOU FIND IT PLEASE?

THIS WAS A QUESTION FROM LAST WEEK AND THE RESPONSE DIDN’T GET FOLLOWED UP ON.

SAME ISSUE, NOT SPINNING OUT CORRECTLY

SAME ISSUE, NOT SPINNING OUT CORRECTLY.

THE UNIT ISN’T SPINNING OUT PROPERLY. I’M NOT ALL THAT FAMILIAR WITH THESE UNITS AND I’M NOT SURE WHAT THE ISSUE IS.

My Maytag dryer will not heat.

The Plastic piece is cracked on my Maytag washer.

Having an issue with a Washer

My Maytag washer is not working properly.