Brand: Maytag

Hi, I watched your video on the clogged washer and got as far as taking the dasher out but we can’t get the tub to come out. Do you have any suggestions?

E01 and F01 coming up on Maytag Maxima front load washer.

Looked online and technical manual both say check wiring from door latch to CCU or needs new latch. I tried a new door latch still error won’t even lock or start. Checked CCU board for burns looks good, checked wires for continuity good..
Could it just be needing a new CCU AND will I have to program it to take $2 dollars again for a wash with the new board or is that a separate computer inside the coin slot thing? Please keep the answer simple brain dead after this one.

How do you reset the control panel on a Maytag refrigerator, model #MFI2569YEM0 display board lights up when you touch any button beeps when you push water or ice button but no lights unless you push a button

The right door on this refrigerator pops open when the left door is closed first. I replaced the door cam, part #12028505ap but it did not stop this from happening. I have been telling my customers to open both doors and close the left door first in order to insure both are doors are sealed properly. I have not found an answer on the web. Hopefully your repairmen have found a solution.

Thank you!
Mel
My Appliance Repairman Inc.

HAVE TRIED DIAGNOSTICS WHAT ELSE CAN I CHECK BESIDES DISPENSER AND LINKAGE

found no loose wiring …in self diagnostic test the door locks will not advance through steps in test …only way to get door open again is to manually unlock it …original complaint washer stopped in spin cycle water still in tub door will not unlock

I have a Maytag 4000 Series Washer model# MHWE450WW01. This started about 2 weeks ago. I had an F71 error code. When I hit the power button I’d just get 3 beeps, no display. Found a Youtube video from an appliance tech who said F71 was a motor control board. Replaced the motor control board and everything seems fine until I ran a whole cycle and had wet clothes at the end. Everything seems fine except I get no high speed spin. Thought I might have got a bad board so I contacted partsimple.com and they sent me another board. That didn’t change a thing except to confirm the board was ok. I then replaced the control board. That didn’t change anything.

Here’s where I’m at now: In diagnostics it will spin at full speed with the C08 diagnostic test which tells me I don’t have a mechanical problem like a slipping belt, motor etc. During a normal wash cycle it will not spin at high speed with or without clothes in it. The door locks fine, door lock indicator is lit and door won’t open. It fills to the normal level and drains fine. Spin light comes on but the drum rotates at wash speed. It acts like a load balance problem. The drum rotates one way, stops, rotates the other, then the drain pump comes on and it tries to spin but then stops again, rotates one way then the other like it’s trying to balance the load. I can’t locate the balance sensor (if there is one). Any help would be appreciated.

E01 and F01 coming up on Maytag Maxima front load washer

My Maytag washer is displaying error codes and the door will not come unlocked.

Washer gives f35 and sud error. Trap is clean, technician came and replaced the switch. Washer worked for about a month, getting f35 and SUD error again. Basket is clean. Please help.

Hello, I pulled the cover off my igniter on my gas dryer, and the flame will ignite for about 5-10 minutes and then goes out.

Steps on programing board.

my dryer is making a loud squealing noise.

The Maytag 2000 washer is tearing clothes when a full load is being washed. I observed a towel getting stuck between the tub and the white plastic (bellows?) Is this the right part to replace and can you give suggestions on how to replace this part. The white plastic band that circles the tub inside is well worn and looks ruff. I believe this is the bad part. Does the washer come apart from the front or the top. There is a dryer stacked on top of the dryer.

I can dispense water but not ice. I took the ice maker out and found a couple ice cubes in the forms and some empty ones. It dropped one ice cube the other day. I couldn’t find an ice blockage anywhere. How do I know if I need a new ice maker , valve, or other part?

Customer icemaker not producing ice. No water in Mold. No 120vac to icemaker at test points. Tried jumping. No movement. Tested harness checks for continuity. Replaced icemaker anyway just to check my diagnostics. No power to new icemaker. This unit uses. Adaptive defrost and control boards..
What do I test next? What part supplies power to icemaker and where is it located? I believe boards are located in fresh food section. Your help is appreciated.
G
Newtech2012