Brand: Whirlpool

The water dispenser in the door gives me water for a very brief couple seconds and then just trickles out like it’s not on or something. I seem to still be getting ice made so I have no clue as to why the door won’t give me water. What can I check to figure this out myself?

I’ve got this thing apart and have been checking parts to find the problem. It was tripping the breaker consistently and now I’m not sure what’s causing it. Checked the board, seemed fine. Checked the igniter, also good. Getting proper power to and from unit and the wall, so can anyone help me out?

my freezer quit working. i ordered the board and replaced it, with it came a new touchpad and it said i have to replace it also. how do i do that..

Didn’t get any voltage across the heater element terminals on my WED9470WW1 Duet dryer. Pulled wires from high limit thermostat and thermal cutoff on the heater box. Got continuity on both. The heater element had continuity as well when tested with its wires removed from the terminals. Getting 240v from the outlet. Don’t know what to would be most likely culprit to check next. On the blower housing, the fuse has continuity, the only weird thing I found is that the thermistor has a resistance reading of 14k ohms. in 70 degree room temp. Heard these should be around 12k ohm. Could this cut the heat? Or is controller or controller relay higher probability of fault? Can the controllers relay be tested? BTW best video on the topic. Thank you !

Our dishwasher comes on, lights up, and fills, but then won’t actually wash. It just stops and there’s almost a low hum noise. My husband got it to cancel and drain and I redid it thinking it was a fluke, but exact same thing happened. What should we do from here?

Our dryer seems to be getting too hot and then shutting down. Normally I can wait and restart it to finish a load but not always. We’re on a 2nd story of a duplex and I tried checking the outside venting, but it looked clear where it exited the house. Any other thoughts? Could the hi limit fuse just be going bad? Or maybe the thermostat?

My washer is making some very unusual and strange noises during it’s cycle. I just got it not long ago and I don’t ever remember my old one sounding like this. How would I know what’s normal and what might be a problem? Should I have a service call on it just to make sure? I’d hate to let something go that could cause damage down the road.

So my refrigerator is completely broken with the cold air switch not functioning and the lights don’t work. The cold air functions a little only when i turn it off but when i put it on low-medium-high setting, it completely does not work. The three lights do not work but the light bulbs are brand new. To resolve this, i replaced the bi-metal defroster and defrost timer for the refrigerator. But the results are the same and my refrigerator is still broken. Any suggestions as to how i can fix this?

I have a code 90 when I run the diagnostics from the panel. My dryer will beep 3 three times when after pressing power and then pressing the start button. The drum light is not lit but tested good. I’m thinking it’s the door switch, correct?

dryer flame comes on turns off not drying (on and off)

My ice wouldn’t come out so I aimed my hair dryer up the despencing hole in the front. Held the rubber black flap up with a wooden spoon and I think I knocked it out of what ever holds it in place because it won’t work now and you can move the piece up and down. how do I get that put back in the slots>

washer not starting.
i checked:
1. Breaker
2. Lid lock
3. Power outlet
ALL is in tact and working
I did the LRLRRRLR to put it in diagnostic mode but never got any lights on or even blinking
Please help

I Have a Whirlpool Gold French Door Refrigerator
M/N:GX5FHDXVB03 S/N:K02386807 purchased on 6/21/2010.
-The Vertical Mullion Rail (Flipper Mullion) is very warm or even hot to the touch.
-The freezer, set on the warmest setting is too cold.
-The refrigerator is not cold enough.
-After the internal controls for the refrigerator and the freezer are both set to off, the unit continues to sound like it is running. This stops only when it is unplugged.
How should I proceed?

HELP!
We are unable to take off the drain lid and the water wont drain from the dishwasher.
We cant find any videos on your site or ytube to help us.
Can you assist, my mom is frustrated!
Thanks, a son
We have a whirlpool dishwasher

Unit will only start in diagnostic mode. When I first start diagnostic mode, all lights are green. The unit Will get a few minutes in to diagnostic mode and dies, no lights and the unit will not respond. It will only respond trying to run diagnostic mode, always get the same result, it dies and is unresponsive.

I checked to see if the chopper blade was jammed, it was not. I replaced the control board, that did not fix the issue.

Any ideas. Could it be the thermal fuse? Would diagnostic mode still try and work if the thermal fuse is bad?

I tried working through the service manual attached to the inside of the kickplate but there wasn’t anything in the troubleshooting that referenced what to look for when the unit died during the diagnostic mode.

I assume that once the unit got to somewhere in diagnostic mode that wasn’t working properly it shut down…

Any ideas or feedback would be appreciated.

My evaporator fan is not running and I think has failed. I couldn’t find anything based off my model number and am going to try and replace it. I found a part number that is think is correct, could someone confirm for me? Number is 12013209Q.

Our range is beeping non-stop and flashing the aforementioned error code. From what I could find online, this is a shorted keypad. So what part do I need and is there a video that could show me how? I really don’t want to have to get a new range and am hoping this won’t be too difficult.

Our dryer isn’t heating up. My husband checked the coils because I heard that was a typical repair, but they are fine and working. What else can we check?

It does everything else great but it stop throwing water in during the rinse cycle.

I had asked the question in reference to this video that oyu guys posted
https://www.youtube.com/watch?v=IEr9A7uhdN8

thanks,

What is the ice maker (replacement) part number for this fridge?

Will the module part number 101 90935 fit the ice maker corresponding to this fridge?

Thanks in advance.

I think I have a hose leaking on top, but I can’t raise it up.

I have been having problems with my washing machine. The lid lock light begins to blink throughout different parts of the cycle. When this happens I have to pause the whole cycle, wait for light to stop blinking and unlock, and press start for it to lock again to continue throughout the rest of the cycle. I have to do this several times in order to complete a load of laundry. I did a diagnostics test like you said too in one of your videos, but I do not have the sheet to tell me what my error code means. The first set in the error code was sense, rinse, spin, and done.. Followed by the second set which was only the done light. Can you please help me figure out what this code means as well as why my lid lock begins to blinking numerous times throughout every cycle?

I have a Whirlpool Duet gas dryer, GGW9200LQ0 that is roughly 12 years old. It runs and generates heat but in the last 10-11 months it has been taking too long dry a load of laundry (unlike its first 11 years of service)

I have previously disassembled it and vacuumed out excessive lint from the internals. This seems to help for some time but I need to do it again after 6 months.

The dryer does not turn off during a cycle but it doesn’t dry clothes completely. E.g. a 90 minute high heat cycle leaves 6-8 pairs of jeans warm and damp.

The dryer was moved to my basement about 10 months ago and a new rigid venting line installed (no screws). It’s about a 12′ run of venting upwards to a ground level exhaust vent and has about 3 elbows in the venting run. I just disassembled the venting and had to clean out lots of lint in the venting again.

I know how to test the thermostats, is there a way to test the other combustion components for problems? Shouldn’t the lint screen be catching more of the lint than this?

Also – how often should the thermostats, moisture sensor bars, coils and ignitors be changed? Would the drive belt, rollers and idler pulley be due for replacement at 12 years of average use?

Hello,
My husband is trying to diagnose of our refrigerator is dying. He says the fans seem to be running but it’s not cooling. He’s thinking compressor but I wanted to know what else we could check before deciding to get rid of it or attempt to fix it. Thank you ahead of time.

I have an electric dryer that I can’t figure out. It’s not heating and I initially thought it was the element. I got it apart and checked that, but it seems fine. Then I found a video on here suggesting the thermostat, but that is also coming back fine. What a I missing?

I have an odd problem, our duet washer is filling, with hot water only, when completely turned off and not in use. I came down to do laundry and found quite a substantial amount in the tub already. I drained it and did my load, and then checked the next day and same thing. I have a feeling this is also causing our hot water heater to run more than normal since the water is actually warm. Any help is appreciated.