Brand: Whirlpool

Ice bucket in the door is freezing into a block and won’t dispense ice the door appears to tightly closed and cubes appear to be good quality any ideas on what could be going on with this problem. Thanks in advance

I have a Whirlpool dryer It keeps blowing thermal fuse by blower (part 3392519). I replaced thermistor (part 8577274) and thermal fuse about 4 months ago. Checked venting and it was clear, customer had it cleaned out about six months ago. What else could be causing this?

The cooktop light on my stove would not go out when all of the burners were turned off. I found your video on fixing the switches when this happens. I was able to remove the faulty switch pretty easily thanks to your video. I am now waiting for the new switch to arrive. In the process, I have left the back panel off of the stove. I noticed last night that when I turn the switches for the burners that are still connected that they will sometimes spark. Is this normal? My fear is a fire hazard. Am I witnessing all of the switches going bad all at once? Or is this normal or possibly just dust getting burned off and once the back panel goes back on will resolve itself.

The switches do not arc or spark when not in use and it only happens when the initial turn happens. So again, is this an issue?

Thank you for your help.

HAVE A WHIRLPOOL REFRIGERATOR .
The water tank is in the fresh food ceiling under cover.
It is made of 2 separate tanks, I large, I small..
Fitting connecting the tanks cracked and I ordered new tanks ( PN W10277923 ).
This partnumber shows both tanks but I have ordered twice and have had the large tank only in box.
Anyone know of a different number for both or a seperate number for smaller tank..

This is an upright freezer only. I recently replaced the non-working evaporator fan motor with a new OEM motor. I placed a data logger in the freezer for 3 days. Temperatures in the top are averaging 30 degrees and the bottom shelf zero. Complaint is food is soft on the top shelf. The frost pattern on evaporator was good. The freezer is loaded up pretty full but it appears to me that there is adequate space for air to flow. One thing I noticed was when I would pull the evaporator wall forward the evaporator motor fan motor sounded like it would speed up. I’m not sure is this is just because I could then hear the fan better or if it was actually speeding up due to less restricted air flow. There was door seal problem as well but this was corrected before I placed the data logger in place and the seal is good. The cold control is set on #5 which is colder than the customer normally had to set it. I was wondering if I need to replace the cold control or if the evap motor is possibly spinning to slow. Thank you

Ice maker is not working I have a reverse osmosis water filter , could this cause my issue ?

Freezer evaporator coils have no frost on them, however the fresh food is keeping temperature. I know these units are problematic with sealed systems. Which evaporator is the most common to change and what is the easiest way to tell which one needs changing, because I have seen this same situation before and it be the fresh food evaporator and I have also seen it been the freezer evaporator. Any advise would be greatly appreciated. All fans work.

My Whirlpool washer will not spin out.

My Whirlpool dryer is making a loud noise not heating and has a burning smell.

There is frost build up in the freezer section of my Whirlpool refrigerator. It is just on the very top of the freezer only, its a top freezer model.

My whirlpool dryer is not tumbling.

I dropped the lid on my whirlpool washer and now it will not start.

My gas whirlpool dryer is not heating. What are the most common problems that are the least expensive to repair.

This is an upright freezer only. I recently replaced the non-working evaporator fan motor with a new OEM motor. I placed a data logger in the freezer for 3 days. Temperatures in the top are averaging 30 degrees and the bottom shelf zero. Complaint is food is soft on the top shelf. The frost pattern on evaporator was good. The freezer is loaded up pretty full but it appears to me that there is adequate space for air to flow. One thing I noticed was when I would pull the evaporator wall forward the evaporator motor fan motor sounded like it would speed up. I’m not sure is this is just because I could then hear the fan better or if it was actually speeding up due to less restricted air flow. There was door seal problem as well but this was corrected before I placed the data logger in place and the seal is good. The cold control is set on #5 which is colder than the customer normally had to set it. I was wondering if I need to replace the cold control or if the evap motor is possibly spinning to slow. Thank you for any advice.

Had a whirlpool dryer , ( LINT FILTER ON TOP ) last week, customer complained very noisy and walks on floor.
Found blower wheel shattered, about 10 pieces up to 2 feet into vent tube.
Order part, ( more expensive wheel) return to home and pull drum to lock shaft tand remove and install new blower.
The motor has a 2nd idler shaft next left of the main shaft and a pulley system between them
which looked like it increased the blower wheel rpm. My guess, over 3000 rpm
They also decreased the lint filter chute port to about 1/2 of original size.
Outlet airflow pressure seemed higher velocity, probably designed for lower volume, higher pressure or something..
Changed the blower and found dryer had originally run long enough to also overheat the
element making it sag and short to frame. This caused temp to rise and kick off the
small thermal fuse ( 3392519 ).
Dryer is much noisier design then the original version and I was wondering if this is
a test version or have they switched designs. Any input is greatly appreciated

We have a Whirlpool refrigerator that the water line is freezing in the freezer door.
The freezer temp is fine. This customer has had this problem from new.
Normally she would leave the dispenser light on during the day and when they got home at nite it was fine.
Is there a kit that I’m not aware of?
Any and all help suggestions would sure be appreciated.
Thanks in advance Ben

There is a fuse link in behind the control board on this model that is blown. It resembles a diode a little. I cant find this part on any drawing and was wondering if you could help me with the part number to this fuse?

My whirlpool refrigerator has water leaking down the inside.

The back left burner on my Whirlpool range is not heating.

There is ice build up in the bottom in the freezer section of my whirlpool refrigerator.

Have a Whirlpool refrigerator Complaint, was leaking and small ice cubes and water in the fresh food floor.
The filter is in top right of fresh food compartment and the water lines in / out had molded plastic elbow fittings.
Both hoses cracked at the fittings . I replaced with new modified water lines ,now no leaks.
Cust said Icemaker still making very small cubes. { small icemaker mounts in freezer door ).
Anyone have a tech sheet on the icemaker and/or the manual for this refrigerator.

I AM TRYING TO FIND OUT WHY WHEN I PUT TEMPERATURE SELECT TO HOT ONLY COLD COMES IN . I HAVE CHECKED HOSE FOR CRIS CROSS I HAVE TRIED OTHER SETTINGS AND WARM DOESN’T WORK MACHINE IS ABOUT 6 MOS OLD AND WE HAVE ALREADY HAD SERVICE ONCE FOR THIS ISSUE. THE TECH SAID YOU ONLY GET A MIXTURE OF COLD THEN HOT BUT I LET IT FILL ALL THE WAY UP ON HOT AND AM ONLY GETTING COLD. IS THERE A WAY TO FIX THIS ISSUE. I THINK MAYBE TEMPERATURE SELECTOR SWITCH MAY BE DEFECTIVE.

This is a French door model with ice/water in door. Controls on door. Upon arrival freezer was reading 4 and refrigerator 44. Controls were set for those settings. Do not see a damper assembly in fresh food section. Milk on door was frozen and , as well as other things. Looking at parts breakdown, only evaporator in freezer. So other than possibly thermistor or control board, what else is there thanks in advance.

There is ice build up in the bottom of my whirlpool refrigerator

My electric whirlpool oven is not working.

My Whirlpool refrigerator is not getting cold enough in the fresh food section.