0 votes
335 views

wash motor turns of after about 15 minutes of run time…motor won’t start again on any cycle or in diagnostics. Cycle continues to end. Motor will start again after a period of time but does the same thing. 1 diagnostic code 4-3 motor not running. d/w 1 1/2 yrs old

0 votes
377 views

when I put it on for hot water the hot water valve will come on then the cold water will come on and mix both for a little then only cold will remain the hot will go back on for a few seconds and cold etc etc

  • zelik123 asked 1 year ago
  • last active 1 year ago
0 votes
237 views

washing machine lock does not open …..had to do manually work fine for few weeks and does again……

0 votes
203 views
  • rfcorral asked 1 year ago
  • last active 1 year ago
1 vote
323 views

Water in unit not getting heated and not drying dishes, element not coming on.

  • twinlab asked 1 year ago
  • last active 1 year ago
0 votes
362 views

i’m trying to figure out what problem it may have, so it can be repaired.

1 vote
220 views

replaced 4 suspension and the sensor problem not fixed
what do you think is the problem

  • fritze01 asked 1 year ago
  • last active 1 year ago
0 votes
326 views

Is this a power board issue? No LEDs work in the refrigerator or freezer and in the pantry. Also the pantry control interface doesn’t work. In the service mode the Fresh food and the freezer thermistor tests #1 and #2 will not show Pass or fail (01 or 02). The fresh food door switch test show that they are not working. ALL the harnesses are good and connected. The customer said this has been going on since Christmas.

Any help will be welcome.

  • Pancakes asked 1 year ago
  • last active 1 year ago
1 vote
281 views

CAN A LID SWITCH CAUSE NO LIGHTS COMING ON. GREEN LIGHT ON BACK OF CONTROL MODULE THE ONE WITH PRESSURE LINE ON IT. I REPLACED THE MODULE WITH A GOOD ONE I HAD IN STOCK AND NO DIFFERENT.

  • Guest asked 1 year ago
  • last active 1 year ago
0 votes
491 views

I have this Whirlpool dishwasher that I replaced a broken heating element and once I replaced it I tested it under a diagnosis and LOAD test I was able to confirm that this heating element is working and heating however, when I use it in normal mode it does not heat as far as I understand that the error codes have to be cleared in order for the heating function to work again. I did try the service diagnosis by hitting three buttons 1-2-3 1-2-3 1-2-3 and going into that and getting into service diagnosis mode run and letting it complete Is there a step missing as far as clearing the error codes from this ?
If the error codes are not clearing does mean a faulty computer?

  • Tca2018 asked 1 year ago
  • last active 1 year ago
0 votes
248 views

FAN RUNS EVEN WHEN MICROWAVE IS OFF AND CODE 161. WHAT COULD IT BE ?

  • Guest asked 1 year ago
  • last active 1 year ago
1 vote
399 views
  • jmcgee707 asked 1 year ago
  • last active 1 year ago
0 votes
323 views

DISHWASHER WILL NOT DRY DISHES WELL, HEATER HAS BEEN REPLACED AND DOES HEAT BUT CUSTOMER STILL COMPLAINS THAT DISHES ARE NOT DRY ENOUGH, WATER DOES NOT GET HOT ENOUGH.

LOOKING TO SEE IF THERE IS SOME SORT OF A SERVICE UPDATE FOR THESE NEWER STYLE WHIRLPOOL DISHWASHERS, WE SEEM TO RECEIVE MANY COMPLAINTS LIKE THIS.

THANKS

  • halco1242 asked 1 year ago
  • last active 1 year ago
1 vote
335 views

the ice dispenser when the button is pressed and released it keeps running

  • bill8321 asked 1 year ago
  • last active 1 year ago
0 votes
262 views

Hi I was looking for a service manual for r this particular unit

  • Tca2018 asked 1 year ago
  • last active 1 year ago
1 vote
398 views

This is an oven/microwave combo. Oven works fine and microwave works good except for it will not run longer than 1 minute. At that point, in the oven control board screen it will give an error code of F3E2. The microwave board doesn’t display this code. The oven sensors check fine as well as the oven works great! Not sure what this could be causing this as all works well except for the 1 minute time issue. Set for 3 minutes will cut off completely at 2 minutes. Any time frame will do the same.you can also start the microwave back up instantly and it will run for 1 minute. Any help would be great!!!

0 votes
287 views

I need the troubleshooting steps for dishwasher please.

0 votes
286 views

After make ice and fill bin start melting ice completely

0 votes
286 views

During spin cycle, it is very loud, as if the bearings are bad.

0 votes
538 views

I need a video for this washer

  • burtyost asked 1 year ago
  • last active 1 year ago
0 votes
322 views

GE Dishwasher GU2275XTVY0 Latch-Door was replaced because door wouldn’t close & power light blinking,
Next day power blinking again.won’t work at all, water was filled in half way

Bi-Metal fuse was checks good at first repair.
Would you have service Manual & Cures

  • daniely asked 1 year ago
  • last active 1 year ago
0 votes
346 views

I would like to know how to perform a factor reset. How do you perform a reset of the main broad to clear out error codes? Appliance is a Whirlpool dishwasher

  • GeekJames asked 1 year ago
  • last active 1 year ago
1 vote
385 views

error f70

0 votes
295 views

I’m not seeing a damper in refrigerator save in I/M room. Crisper and side controls off. Where is this refrigerator getting it’s cold air and how is it controlled? From Ice room and or freezer evaporator? Where are the vents for the air? Thank you.

0 votes
273 views

Any bulletin related to refrigerator evap making noise or improper cooling?

0 votes
375 views

Customer said they saw a flash on the bottom part of the freezer when they open the door.
and ever since then the ice maker is not working if I push the lever on the door to the Spence ice the flap will open but the edge of food will not turn and the unit will not make ice.
The unit however does dispense water

  • zelik123 asked 1 year ago
  • last active 1 year ago
1 vote
365 views

Does this unit have any service flashes or job pointer concerning the bake burner and spark ignitor kit .This is a DSI system? The gas ports are clean. The oven has run for years with out the Ground supplied through the outlet. The wiring is good. No bare insulation.

Is there a service manual available?

  • Pancakes asked 1 year ago
  • last active 1 year ago
0 votes
552 views

This Unit was violently Shaking, I replaced the Washer Suspension Rod Kit, W11130362
It still Shakes, It seems to have a Problem Spinning up also.
Ideas?

  • thosk1051 asked 1 year ago
  • last active 1 year ago
0 votes
368 views

Im having issues with condensation build up behind the icemaker compartment inside the refrigerator room. I know previous models had the same issue but the kit helped with the problem. Is there anything new for these models?

Showing 31 - 60 of 1k results