0 votes
9k views

My Electorlux range is getting an E31 error code.

0 votes
899 views

My Electrolux washer is displaying a 42 error code and im not sure what it means.

0 votes
2k views

Two year old refrigerator making ice but not dispensing through door. Water dispenser is working. What is most probable cause?

  • colin asked 10 years ago
  • last active 10 years ago
0 votes
2k views

Unit will not make ice or dispense water. Water flow from valve thru filter head good. Have water going to water reservoir, but not out. Looking inside refrigerator there is an ice block on the lower right side of water reservoir cover. Any help is greatly appreciated.

0 votes
2k views

The washer only leaks when in the spin cycle. When washer goes into spin it will start leaking from the center where the transmission goes thru the tub and it makes a grinding noise. If I replace the spin bearing will it also stop the water from leaking. Thanks Ricky

0 votes
2k views

My Electrolux refrigerator is not cooling properly.

0 votes
2k views

My Electrolux washer seems to be off balance.

0 votes
3k views

Door handle loose how do I check or tighten hardware inside door

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

I just replaced the thermostat and found the evap fan motor cycling on and off about every 2-3 seconds. Is this a bad motor or board or ?
Why is it cycling? I have never come across a cycling motor before. It either worked or it didn’t. How can I check to determine IF it is a failing motor?
Thank you

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

Clothing gets stuck, tub moves around a lot, bad smell, standing water.

1 vote
2k views

Our Electrolux refrigerator dispenses ice intermittently. It spits ice out on the floor. We have had to shut the water off or it will spit water also. With the water off you can see and hear the dispenser turning on and off at all hours of the day or night. I need to dig into the parts to see if it is a loose wire or faulty control panel?

I need help with how to pull the stainless ring off the control panel to get at the parts.

Has anyone solved this issue before?
I have seen it reported as Casper the friendly ghost.

Thanks,
Tom

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

I’m trying to replace the main power board. replaced old board but the fridge dose not start up, no lights nothing, controls dead. I also replace the thermistor
Reinstalled old board fridge started up, lights working, controls working.
Installed another new board. nothing.
Fridge is also missing the tech sheet.
Initial problem, Items freezing items in fresh food section,
Thanks for your help

  • rfcorral asked 5 years ago
  • last active 5 years ago
0 votes
840 views

My Electrolux washer is off balance and shakes around when in use.

0 votes
2k views

Your video shows how to diagnose the problem, but not how to fix it. Thank you for for the diagnostics, video that was very helpful. I really need a video to remove and replace.

  • Christina asked 10 years ago
  • last active 10 years ago
0 votes
2k views

I’ve tested the air flow with a meter it is poor I’ve tested the igniter everything else inside is working fine there was a tremendous amount of lymph build up inside the machine cleaned everything out and still getting poor airflow reading

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My washer will not spin. Any suggestions?

0 votes
2k views

My Electrolux Refrigerator drawer will not open.

0 votes
2k views

THE EVAP COIL HAD A LEAK WHICH I REPAIRED. I RECHARGED THE SYSTEM. I HAVE 0 PSI AT THE PROCESS STUB AND ABOUT A 70 DEGREE DROP ACROSS THE CONDENSING COIL. THE UNIT ISN’T COOLING PROPERLY STILL. THE TEMP DROP ACROSS THE COIL HAS ME STUMPED AS SEEMS TO ME THAT IT SHOULD BE WORKING. ANY THOUGHTS? TX

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

Evap fan motor cycles on and off It started out cycling about every 2-3 seconds. After a couple of minutes it cycles to the point that it continues to turn, but not a full speed.
1. What causes this?
2. If it is the board, how do I test it to determine that it is the board?
3. If it is a bad motor (?) how do I test this?

I’ve never tested a fridge board or run it through a diagnostic test.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

E40 error, E47 error, washer starts then shuts down.

0 votes
2k views

No heat.

1 vote
2k views

I need to remove the stainless steel trim ring that surrounds the ice/water dispenser. Do you have a technical manual showing how to do this? I don’t want to damage it. I don’t see any exposed screws.

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
1k views

My washer is displaying an 84 error code.

0 votes
2k views

Can Reverse osmosis filters be used on ice makers ?

0 votes
2k views

Has error code on display , do you have service sheet ? Thanks

0 votes
2k views

My electrolux refrigerator is not making ice.

0 votes
2k views

Ice dispenser not working properly.

Showing 61 - 90 of 201 results