Hi!
The problem is the following:
1. After turning on of a refrigerator, it works for ~2 hours, temp. goes down to -20 and +5 in freezer and cooling chamber, compressor stops
2. Then, after 10-15 minutes, it tries to start for 8-10 seconds, producing loud clicks and then stops. Freezer fan is working all the time.
3. Temp. goes up to +10 in both cameras, producing A1 or A2 alert.
If I give him a rest for 4-5 hours, this cycle repeats.
But some times (I don’t know why) this scheme breaks – compressor works (normally?), but temp. in cooling chamber rises up +10, meanwhile temp. in freezer drops to -26-27.
Thus, there is strange behavior – sometimes it seems to make vacuum in freezer, after the door is closed.
- Anton asked 9 years ago
- last active 9 years ago
The unit will agitate and drains but it will not go in to spin
Please advise
- Guest asked 6 years ago
- last active 6 years ago
The code is telling me the the cold side of the water inlet valve is letting it spin.
- Scales asked 3 weeks ago
- last active 3 weeks ago
at first neither fan condenser or evap fan not working replaced condenser motor now works but evaporater fan not running be odd both fans failed at same time how can I test evaporator fan I replaced condenser now works do you think its computer board or bad evaporater
- Guest asked 9 years ago
- last active 9 years ago
My microwave is making a grinding sound, and I’ve replaced the turntable motor, but the noise has not gone away.
- Deann Russell asked 10 years ago
- last active 10 years ago
- Guest asked 10 years ago
- last active 10 years ago
It’s gas by the way. What part would I need?
- Tyler A asked 10 years ago
- last active 10 years ago
THE HOTPOINT MICROWAVE DOEN NOT OPERATE BECAUSE THE THERMOSTAT AT LOCATION#: 138 ON THE DIAGRAM DOES NOT HAVE CONTINUITY. THE PART# IS WB27X11213 110/0.
THE MARKINGS ON IT IS KSD210 AND 70.
IS KSD201 THE GENERIC PART NUMBER, IF SO WHAT DOES THE 70 MEAN?
IS IT’S ROLE TO PROTECT THE MAGNETRON?
I NOTICED LOCATION# 117, PART#: WB27X11208 70/0 AND LOCATION# 138, PART# WB27X11212 120/0 AND LOCATION# 130 AND LOCATION# 130, PART#: WB27X11210 160/0 ARE ALL GOOD. IF THE 70 IS A TOLERANCE LEVEL, COULD THIS HAVE BEEN WRONGFULLY MIXED UP WITH LOCATION 117 THAT HAS A 70/0 NOT LOCATION 138 THAT HAS 110/0? DOES IT MAKE THAT MUCH OF A DIFFERENCE? IF I REPLACE THE THERMOSTAT THAT IS BLOWN AT 138 WITH A HIGHER NUMBER, FOR INSTANCE, 110/0 INSTEAD OF 70, MIGHT IT DELAY BLOWING, THEREBY DAMAGING THE MAGNETRON?
- Guest asked 6 years ago
- last active 6 years ago
I’m curious as to what would be causing my gas oven to preheat and beep as if ready, but then not maintain it’s temperature after that?
- Stephanie A asked 10 years ago
- last active 10 years ago
Do you have the service manual for rvm5160dh1ww- is a hotpoint and for jvm7195df1bb- is a GE? The ge comes one but does not heat. How do I eliminate the control board from the magnetron and magnetron thermostat?
- Guest asked 6 years ago
- last active 6 years ago
- terrell asked 9 years ago
- last active 9 years ago
My Hotpoint refrigerator is not getting cold enough. It has frost / Ice build up on the back wall.
- Fred Abernethy asked 8 years ago
- last active 8 years ago
The washer will still overflow after replacing the pressure switch and hose. We double check to ensure that the hose is cleared as well. It will also only overflow on the rinse cycle. During the fill cycle it will fill to the proper level and then once it is stopped and turned to the rinse cycle it will not drain out first. We have also tried replacing the timer as well with the same issue.
- Guest asked 6 years ago
- last active 6 years ago
Figured out the knobs are broken but not sure how to replace the start one. Couldn’t find a video to do it myself.
- Willy T. asked 9 years ago
- last active 9 years ago
My Hotpoint refrigerator is not getting as cold as it should.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
During agitation shifter doesn’t work and inner tub and agitator turn at same time.What is shifter voltage and resistance ? The inverter on the motor supply it’s voltage but what timer signal calls for it to actuate? Could my timer be bad or the motor or the shifter. Can you send me a theory of operation ?
- Guest asked 6 years ago
- last active 6 years ago
There is ice building up in the back of my Hotpoint freezer.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
Checked polarity on outlet, check fuse, checked push start switch all good. There’s no power to the start switch. Only place I have power is on the line feed to timer. I’m thinking a bad timer but unsure
- Guest asked 6 years ago
- last active 6 years ago
hotpoint oven the oven and broiler not working
- Guest asked 9 years ago
- last active 9 years ago
My Hotpoint dryer is making a loud high pitched squeaking noise.
- Harley Clark asked 8 years ago
- last active 8 years ago
hotpoint side by side fridge inside lights working compressure hot condenser fan not running either is evaporator fan if compressure not working properly should the condenser fan still turn on not sure what to do next
- Guest asked 9 years ago
- last active 9 years ago
the customer is saying that the oven will go on by itself from time to time
- Guest asked 8 years ago
- last active 8 years ago
My Hotpoint dryer is making a loud squeaking noise.
- Harley Clark asked 8 years ago
- last active 8 years ago
Water slowly leaks into the dishwasher when it is off. So the bottom of the dishwasher has a pool of water if not in use. There was sediment in the water valve, so I replaced the water valve… but the dishwasher is still leaking slowly while off. What could cause this issue?
- Apache Warrior asked 6 years ago
- last active 6 years ago
The element on my Hotpoint stove is not heating, also the clock is not working.
- Harley Clark asked 9 years ago
- last active 9 years ago
