0 votes
52 views

RIGHT FRONT BURNER NOT WORKING; BURNER IS DISCONTINUED BUT IF YOU ORDER SWITCH IT COMES WITH BURNER AND WIRING HARNESS. PART # W10823734. THIS IS NOT THE USUAL INFINITE SWITCH LIKE THE REST OF THE BURNERS. IT LOOKS LIKE THE ONE IN THE KIT BUT EPIC SENSOR NOT HOOKING UP. AM I DOING SOMETHING WRONG.

  • joeski1369 asked 1 month ago
  • last active 1 month ago
0 votes
435 views

The burner and infinite switch part number is w10823734. The espy sensor harness on the old and new sensors won’t work on the new INF SWitch . or would it be simpler to use the old burner with the 12002121 INF SWITCH?

I need a wiring diagram. And any help you can give.

  • Pancakes asked 10 months ago
  • last active 10 months ago
0 votes
264 views

When I turned the oven on to 200° it went to 200° and stopped, I waited and then tried 450° and it went to 450° but then when I tried to turn it off it wouldn’t turn off and then got the error code F2

0 votes
177 views

the ice maker is not working on this unit. i checked for power at the L N on the ice maker and i didnt get anything, so i replaced the ice maker. however when the new was put in i had the same issue. there is no power to the ice maker

  • zelik123 asked 1 year ago
  • last active 1 year ago
0 votes
384 views

My jennair refrigerator with drawer freezer has been leaking water from the base for a little while.

  • jubalde asked 1 year ago
  • last active 1 year ago
0 votes
314 views

Why Does My Gas Oven Glow Like It Is Hot Even When It Is Not Heating?

0 votes
383 views

What Makes My Oven Smell So Bad When It Is Cleaning Itself?

0 votes
2k views

Oven light turns on by itself , how can I prevent this from happening?

0 votes
308 views

My Jenn Air dishwasher JDB1270AWY has started making a grinding noise during part of the cycle. It is cleaning great and seems to be draining fine. Ideas?

0 votes
455 views

The unit will start to heat and then I get the error code f8e0 underspeed fan.
I do hear and feel the fan blowing.
Please advise

  • zelik123 asked 1 year ago
  • last active 1 year ago
0 votes
426 views

the water valve is in the fresh food compartment. how to replace it.

  • burtyost asked 1 year ago
  • last active 1 year ago
0 votes
303 views

I suppose it is one of the two boards. I need a service manual.

  • Pancakes asked 2 years ago
  • last active 2 years ago
1 vote
409 views

Hi,
The ice maker on this unit stopped working due to ice buildup right on top where the water goes into the ice maker. I defrosted all the tunnels and the ice maker started to work again, the customer called us again two days after and said that is stopped making ice again. Do you guys had any experience with ice maker issue on this unit?

  • bettertech asked 2 years ago
  • last active 2 years ago
0 votes
441 views

Customer said one time no burners would come on when set. Now the right front won’t boil water. Could this be a bad appliance manager board? Both duel elements work. Even on number 10 setting it will go off with a pan of water on it. Any advice welcome.

  • Pancakes asked 2 years ago
  • last active 2 years ago
0 votes
381 views

I would like to know how to remove the mounting screw on the bottom of the unit. Do we have to remove the front door out? Would you let us know? The bottom screws are blocked with front door hinge , and not able to access the screw to be out. Thank you.

  • Jushkim5 asked 2 years ago
  • last active 2 years ago
0 votes
859 views

This code says cooling fan speed too low or won’t come on. Do you have a video on this one and a service manual and any tips?

  • Pancakes asked 2 years ago
  • last active 2 years ago
0 votes
393 views

We are trying to change the Display/ Control Panel to replace it with a new part but we have ran into a wall per say. we can’t manage to get too the panel.

  • Jushkim5 asked 2 years ago
  • last active 2 years ago
0 votes
422 views

door seems to be held on by 2 clips which are attached by some sort of rubber cement. is there a part # for this, or an after market product?

  • tomtech asked 2 years ago
  • last active 2 years ago
0 votes
658 views

Hi. My name is Joe. I am trying to trouble shoot a problem with my above mentioned refrigerator. I touched the water dispenser button to switch it from ice and the blue leds went black. I then tried all the other buttons and no matter what buttons I depress the small display lights up with blue diagonal lines across it. I believe at that time the refrigerator was still operating because I left it for 24 hrs before I started to try to diagnose the issue the first thing I did was to power down the unit for a few minutes the powered it back up. When that didn’t work I left the unit again for about 12 hrs and then we noticed that it was no longer cooling or freezing. I checked the interface board for power and I have 12vdc on two different sets of wires. I just want to confirmation that this interface board is my issue because it’s not returnable

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
618 views

I need to remove the icemaker. do you have a video>

  • burtyost asked 2 years ago
  • last active 2 years ago
0 votes
1k views

ice maker w10377151 has been converted to icemaker W10882923 unclear instructions on how to convert

  • Guest asked 2 years ago
  • last active 2 years ago
0 votes
621 views

Hello Matt and other sr techs.
I requested service information on this Jenn Air range. I felt that the electronic control board was bad. I replaced the control board . I have the almost same symptom . However both boards react in the same manner, when I try to put them in the service mode both will freeze up and some times freeze up before you get into the service mode. Neither bake nor broil will work. Both glow bars come on bake pulling 3.14 amps(with new board) 2.85(with original board) broil pulls 3.49( with new board) 3.25(original board) . With either board you can start into the menu and it will just lock up and I have to reset the breaker to start over. My thoughts are both original and new board are bad. Please advise , any thing you think I might have over looked. According to the manual it takes between 3.20 and 3.60 to open the gas valve. The current only stays over 3 amps on both bake and broil for about 2 to 3 seconds and rapidly drops off.

  • billtilley asked 2 years ago
  • last active 2 years ago
0 votes
708 views

Hello Gentelmen, would like to obtain the service information on this Jenn Air Gas range.
The oven will start to heat at first then shuts down. I noticed the display blanks and clears off .
If you have a service manual, wiring diagram, schematic, service bulletins. Have not made any checks yet.
Any service advise would be appreciated. Thank you.

  • billtilley asked 2 years ago
  • last active 2 years ago
0 votes
699 views

When preheating the unit shuts off at 180f the panel and the entire unit shuts off. All elements and fuses are ok. The main board in the bottom of the unit was replaced.

1 vote
752 views

Then after a day or week it comes back on with time and we can use the oven again. And stays on for another day or two – then goes black out.
I tried rebooting it by shutting circuit off for a minute & the turning back on.
Display unit was replaced by dealer 3 years ago.

  • Guest asked 3 years ago
  • last active 3 years ago
0 votes
495 views

Hello I have a question on a Jenn-Air Oven. I’m noticing these issues: Oven roller rack could fall off

0 votes
764 views

Jenn-Air Oven that is not working

1 vote
809 views

I had a customer today. He had a Genaire gas range. We determined that it was the keypad assembly that was bad. There was an F1 E1 error code. We ordered a new keypad assembly. But while I was there I was looking to see how easy or difficult it was to install the new one.

0 votes
742 views

My dishwasher will not drain the water out of it.

0 votes
973 views

My Jenn-Air dishwasher is not draining properly

Showing 1 - 30 of 65 results