Brand: Kenmore

The filter was just replaced on this and it seems to have made the issue worse. Has a constant drip to it, enough that you need to keep something in the tray all the time to catch it. Any thoughts on what it is?

The subject refrigerator needs new door seals. I believe you just pull the old seals out of their grooves and push the new ones in. Is it this simple or is there something else I need to be aware of? Thank you.

I’m doing the heat pump (circulation pump) on this unit, and want to know if I can do it without pulling the bottom pan (base) off?…..I was able to change the drain pump on one of these units without pulling the base…wondering if it’s possible to do the heat pump this way as well?
Thanks for your help. Rocket.

so i put in into diagnostics mode and i got an error of F6 E1
how can i repair this?
its a Kenmore washer

Customer said that ” Feezer works fine. Its cold in there but the refrigerator is warm. ” I have handled this symptom before on other manufacturers but dont want to assume same cause. Usually frost build up in evaporator coils in freezer section which constricts airflow to fridge section. Should I test defrost heater before testing defrost thermostat or defrost control ?

Kenmore fridge

Model Number
106.57036601
What have you tried so far?
Customer said that ” Feezer works fine. Its cold in there but the refrigerator is warm. ” I have handled this symptom before on other manufacturers but dont want to assume same cause. Usually frost build up in evaporator coils in freezer section which constricts airflow to fridge section. Should I test defrost heater before testing defrost thermostat or defrost control ?

Refrigerator Kenmore
Share
semperfi asked 3 days ago
Answers (1)
Sort by: Newest First
0
0
Hello
You need to check first if their is a heavy even frost build up on the coil. Then next do a continuity test on the heater. If the heater has continuity, then check the defrost thermostat. If the heater and therm. are good then replace the adaptive defrost control.
Information Links
106.57036601 Manual Sears refrigerator | Adaptive Defrost control | 4388932 Defrost control video

The broil element is broken on this stove. Well, it’s not working, and when it did work it wouldn’t turn off. Now we can’t get it to come on at all. Element itself is still intact and in one piece so I’m pretty sure it’s not that. Found the main control failing and can’t find the replacement available through my vendor. Do you guys have it? I’ll just buy from you if so. Thanks for the help on a weekend!

Good day,
My customer has an old Kenmore Side by Side that cuts on and off and it needs this Temperature CTL # WR9X442, but it’s no longer available, discontinued. Do you know of any substitute part# I could use?

Thank you,
Oliver
Primal Service LLC
Atlanta GA.

water is staying at one level

My Kenmore washer will not spin out.

Checked frost pattern today. It was basically uniform except it was slightly heaver on the last three coils. Temperature in freezer was 14 degrees and 30 degrees in the FF section. Controls were set at normal. On Jan 15th the refrigerator controls were set in the middle(normal) Twenty four hours larter the freezer temp was 21 degrees and the FF temp was at 25 degrees. The customer said it took four days for a bottle of water to freeze in the freezer. Evaporator and condenser fan motors are working normally. Damper is manual and works works properly ie opens and closes with the freezer control. Sears Technical assistance suggested suggested replacing the ADC. I’m more inclined to say the thermostat is bad. Any help is appreciated

Software rewrite keeps showing Up date failed, on the manual mode it doesn’t show compressor info as FLSO75LANA.

I have a Kenmore Elite/ LG built washer top load (agitator-less) model will not spin 4 of 9 loads and hear a funny noise from underneath like squealing
it looks like beltless model but there is a shifter for a clutch below. I ran the diagnostics and all seems okay with no clothes inside.
There were no fault codes showing or encountered. Suspect the clutch or main board. the connections look okay. Any suggestions appreciated

The compressor, inverter board and main control board was changed. Before the unit was not cooling (compressor issue) and there was a audile beeping noise also compressor would try to start. NOW after everything has been changed out. There is a clicking noise and the fans will stop momentary and come back on. Also when that happens the temperature display in the top inside of refrigerator will dim. Like I noted, fans will stop and come back on, but the compressor will stay running until set temperature is reached. Please in any way possible. Thanks Ricky

My Maytag dishwasher is unresponsive and will not start.

dryer sometimes runs 10 minutes or less and f 40 error code comes up. checked harness and connections all look good

I have a customer’s Kenmore Elite Oven/microwave combo in which the microwave portion is not heating food. Can you post the tech sheet for this model? I have just about exhausted all means of repair.

This is a washer dryer combo it washes but when it goes into rinse it just drains and spins

I know some Kenmore refrigerators are made by LG or Samsung can you tell me if this one is made by either one of those companies? If it was by LG or Samsung what is there corresponding model number?

I have issues with a Kenmore refrigerator model # 795 7757960 ff code unplug and re plug code reset refrigerator back to normal went on job ran diagnosis code did not appear fresh food fan okay. A day later code back again going on job plan to change fan motor any suggestions will check wiring.

  I went out on service call on a Kenmore bottom freezer/refrigerator. I would like to know how to get the pcb in diagnosis mode. Thanks

My Kenmore dryer is not heating where do I start ?