Brand: Kenmore

whats wrong if display lights up and all buttons selected respond? but then you press start it does not come on

I have a customer who is getting grey ice from her ice maker. Water out of the dispenser is clear. Filter was changed last week in her attempt to correct this issue.
The ice I have seen is a cloudy grey in color. It almost looks like someone added metal dust from a grinder to the water and stirred it up.
Because the water from the dispenser is clear and the filter was just changed, I am suspecting the ice maker mold and will replace the ice maker.. Any suggestion?

I have a Kenmore Elite 796.31512211 that shows thermistor error symbol. I have reseated connectors. Is there any other checks to make before replacing the control board?

GOOD MORNING. THE CUSTOMER PURCHASED A NEW ICE MAKER. I DO HAVE 110 VOLTS AT THE MOLEX TO THE ICE MAKER. I INSTALLED THE NEW ICE MAKER AND JUMPED FROM L TO V AND T TO H WITH NO RESPONSE. I TESTED BETWEEN ALL TEST PORTS AND COULD NOT GET ANY VOLTAGE READING. I THEN INSTALLED THE OLD ICE MAKER AND JUMPED THE L TO V AND T TO H WITH NO RESPONSE. THEN I TESTED ACROSS THE L AND N AND GOT 110 VOLTS. PULLED THE MOLEX FROM THE ICE WATER INLET VALVE AND GOT 75 VOLTS WHEN JUMPED FROM L TO V. THESE TESTS WERE PERFORMED WITH THE FLAP AND DOOR SWITCH MADE. WHEN FREEZER DOOR IS OPEN LIGHT IS BLINK BLINK PAUSE. WHEN I CLOSED THE FLAP IT REMAINED BLINK BLINK PAUSE. NEVER BLOCKED OPTIC EYE WITH MY HAND. ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.

Grinding noise during spin cycle. Does the gearbox need replaced or is there a tub bearing in this model? It makes the noise when I spin the tub by hand. Thanks Ricky

There is no water in the ice maker tray. Water pressure is good. I tried the test switch and it did not actuate the cycle, rotate and fill. Is this a bad ice maker? The ice sensor test passed. There is good air flow. I did not get a good temperature.reading.

I see no place to cycle test the icemaker. The ice maker part number is aeq73130004. The ice bucket has water leaking in it. The ice maker has been replaced 2 times. I am trying to see where the leak is coming from. Thanks Ray

Installed a new board and have been getting beeping sounds I need to do a reset do I not..?

This is a Kenmore Coldspot. The ice maker was replaced 4 months ago. Now the water is freezing up in he chute going to the ice maker.

needed new control board which i changed but now dryer keeps beeping does it have to be rested some how.

can you tell me what this error code of erdh is?

What is the best way to determine what the problem is on the ice maker?

I have a washer that look like its running fine for around 15 min then just shuts off no error or anything.

Good day,
My customer has an old Kenmore Side by Side that cuts on and off and it needs this Temperature CTL # WR9X442, but it’s no longer available, discontinued. Do you know of any substitute part# I could use?

Thank you,
Oliver
Primal Service LLC
Atlanta GA.

Washer won’t run the final spin cycle, it works but stops before the final spin cycle

I have a Kenmore washer that will not remove the water from clothes in final, I have to give a second spin cycle. I have also noticed a moldy smell coming from the washer lately, what should I be looking for in the way of a repair.

The led lights on the interior of the refer were flickering. I went to another site and was told it was the main board. I ordered and received it, installed it and it is still flickering???? HELP

the led assembly eav62052301 comes with a sensor. I replace this part becuase lg tech support told me that this would take care of it but it did not.

Our tech was diagnosing a noise coming from the freezer section of this unit. He found ice build up on the cover of the fan. He took the cover off and found no frost build up on evaporator. He described a partial frost pattern as if the unit could have just come out of defrost. Refrigerator and freezer temps were good.

      318073028 it looks easy but no video to know                                                                                                                                                                                                                                                                                                                                                        

When pressing trying to start washer begins to start has a humming sound and then stops