SPECIFICALLY THE PROCEDURE TO RECHARGE THE SYSTEM AND SCHEMATIC.
TX
- Guest asked 7 years ago
- last active 7 years ago
- Guest asked 8 years ago
- last active 8 years ago
Not spinning fast enough at full speed on spin cycle, seems to drain fine, clothes come out soaking wet
- Guest asked 4 years ago
- last active 4 years ago
I am looking for a service manual or wiring diagram for this gas dryer that has the issue of the motor constantly running the only way it will stop us to unplug or to open the door I am suspecting the motor relay stuck in the closed position
- Guest asked 5 years ago
- last active 5 years ago
I have a washer that the drain pump will only come on for 3 seconds then shut off. Hoses are good and no obstructions. Everything else works normal except drain issue. Steve
- Guest asked 8 years ago
- last active 8 years ago
I need any advice and Tech sheet
- Guest asked 5 years ago
- last active 5 years ago
Need a service manual and instruction how to test lid lock switch.
- Guest asked 5 years ago
- last active 5 years ago
PARTS DIAGRAM, SCHEMATIC AND TROUBLESHOOTING INFO. THANKS
- Guest asked 8 years ago
- last active 8 years ago
REFRIGERATOR WILL NOT COOL, THE FANS INSIDE OF THE LOWER FREEZER DEPART WILL NOT RUN. BOTH FANS WERE CHECKED OK. WAS ADVISED TO REPLACE MAIN CONTROL BOARD (EBR74796430) AND REPLACE PCB SUB ASSEMBLY (EBR64730423). REPLACE MAIN CONTROL BOARD AND UNIT STILL DID NOT COOL. CANT FIND WHERE PCB SUB ASSEMBLY IS LOCATED OR HOW TO ACCESS THIS AREA? REPLACING THE PCB SUB ASSEMBLY WILL THIS REPAIR REFRIGERATOR OR IS THERE SOMETHING ELSE WRONG WITH THIS UNIT? NEED SUGGESTIONS ON HOW TO REPAIR THIS UNIT AND HOW TO LOCATED THE PCB SUB ASSEMBLY UNIT?
THE AREA I LIVE CANT GET ANYONE TO LOOK AT REPAIRING THIS UNIT.
KEN WENSKE
- Guest asked 6 years ago
- last active 6 years ago
Originally, the washer had an LE code. I tightened the bolt in rear that holds rotor in place (4040FR4051C). After that the washer would agitate clockwise and spin just fine, but everytime it tried to agitate counter clockwise it would lock up, the magnets where so strong I coulndn’t even help it turn with my hands. So at this point, I proceeded to change rotor, then stator, with the same result. All the wires looked good except for one ground wire that I repaired. Any Ideas or suggestions?
P.S.—-What is the easiest way to get broke bolt out of tub shaft (4040FR4051C), as I have now successfully broken the bolt off from taking on and off so much I guess.
- Guest asked 6 years ago
- last active 6 years ago
My refrigerator isn’t dispensing ice or water and displays code er 1F. I tried unplugging it and it will reset only to dispense water but doesn’t make ice. Will only dispense water for a few hours then defaults.
- Harley Clark asked 6 years ago
- last active 6 years ago
LG LFX25778ST French door freezer on bottom
Icemaker and water dispenser will not work.
Error code: Er 1F
Please advise.
- Andrew asked 9 years ago
- last active 9 years ago
This washer quit just before the spin cycle and seemed to take an extra long time draining. I checked the pump, drain hose, and all electronic components check out. I still seem to be missing something. Any thoughts?
- Fred Abernethy asked 9 years ago
- last active 9 years ago
Found the element bowed from repeated overheating and the hi limit open. Looks like I’ll need that entire element assembly. What’s the pricing and availability of it?
- James Buchanan asked 9 years ago
- last active 9 years ago
Summary above is per the customer, I’m heading out there and want to take a control with me. Anybody there have the part information for me? Am pretty sure this is the issue.
- Hall Refrigeration asked 9 years ago
- last active 9 years ago
Looks like the gas valve is corroded and so old I on’t even know how it’s worked this long. Can you get me the part information on a new assembly? Thanks.
- Harley Clark asked 9 years ago
- last active 9 years ago
FRENCH DOOR LG FRIDGE ON THE DISPENSOR DISPLAY IT READS ER WHERE THE FRESH FOOD TEMP SHOULD BE AND 1F WHERE THE FREEZER TEMP SHOULD BE.
- Guest asked 9 years ago
- last active 9 years ago
I FEEL THE AIR VENTS. NOTHING.
THE REAR COILS ARE NOT FROZEN.
I REPLACED THE FREEZER FAN.
I REPLACED THE MOTHERBOARD BASED ON ADVISE FROM REPAIR COMPANY.
THIS THING IS EXPENSIVE
I WANT TO CORRECT THE PROBLEM.
THE FANS ARE MOVING.
I ORDERED THE CONTROLLER BOARD FROM AMAZON.
INSTALLED.
IN TEST MODE THE AIR MOVES.
OUT OF TEST MODE THE AIR DOES NOT MOVE.
I HAVE NEVER HEARD OF FREON LEAK EVER.
I DONT KNOW \
ADVISE
- Guest asked 8 years ago
- last active 8 years ago
I have multiple error codes on this unit and its not spinning or pumping the water out. Where do I start ? https://www.appliancevideo.com/appliances/lg-wm9000h-turbowash-washer/
- Fred Abernethy asked 8 years ago
- last active 8 years ago
CHECKED FOUND THE ERROR CODE ER IF PROBLEM WITH FAN
- Guest asked 8 years ago
- last active 8 years ago
My Dryer is staying hot for too long or getting too hot.
- Patrick's Appliance Service asked 7 years ago
- last active 7 years ago
my LG dryer is not heating properly. Do you have any suggestions to resolve this issue?
- Fred Abernethy asked 7 years ago
- last active 7 years ago
Can you tell me what could be causing this issue on a LG Washer? It is having these problems: Grinding sound on Spin
- Harley Clark asked 7 years ago
- last active 7 years ago
