0 votes
2k views

SPECIFICALLY THE PROCEDURE TO RECHARGE THE SYSTEM AND SCHEMATIC.

TX

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
7k views

I have a customer that wants me to convert his LG dryer to LP. It is an LG model # DLG3171. I typed this number into your model # guide, with no results. I checked PartsPro website and that number came up. So I know that it is a good number. Do you have a video for this model # or something close to it showing how to take it apart? And 2, how long should a job like this take?
Thank you
Bob

0 votes
2k views

Condenser fan cycling on and off every 10 seconds. everything else is working fine.

  • Guest asked 9 years ago
  • last active 9 years ago
1 vote
1k views

The water valve for this refrigerator is leaking. The problem is that the valve LG is saying that it needs is a MJX41178908, the mounting is perfect but this valve is a single solenoid valve. The original vale is a dual solenoid valve but they give no instructions to convert. I wanted to see if you have run into something like this before, get advice, or see if there is any instructions on this. There is another valve MJX41869202. THe valve that is in there is way different than both. Amy advice or research would be greatly appreciated.

0 votes
2k views

my LG dryer is not heating properly. Do you have any suggestions to resolve this issue?

0 votes
2k views

I am a tech –retired think I can troubleshoot well but know the value of schematic and parts

  • Jerry asked 9 years ago
  • last active 9 years ago
1 vote
2k views

I replaced ice tray and clip for thermister on tray. It is seating properly and firmly against the bottom of the ice tray. Ice maker actuated but when rotating tray 1/2 inch it hits Icemaker arm I suppose a switch inside arm tells Icemaker to return to original position.

I primed the ice tray with some water and it dumped the cubes in the bucket but did no subsequently fill with water.

I checked the water valve by temporarily moving the dispense connector on the water valve to the ice maker water valve and water flowed into ice tray when I pressed water dispense on outside of fridge.

How do I do an electronic fill test using diagnostic mode . I am buying Icemaker and would like to fully test before leaving the location .

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
2k views

First off, I did not see an error code as the screen was black, even though the machine was still running.

Problem: Door spontaneously flew open at the start of the rinse cycle when the machine was filled. It happened twice (yes, I tried it again), both occurring at the same time in the cycle. It doesn’t seem to be the lock mechanism, because it locks perfectly during the rest of the time. I’ve used the machine since to spin hand washing, and it works fine. Your help is appreciated. Thank you

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
2k views

HI,
How do i get the front panel off of this dryer?

Thank you,

Mike

  • michaelm asked 6 years ago
  • last active 6 years ago
1 vote
1k views

I haven’t been on the call yet but I have an LG dryer that has a burning smell once it starts up

  • allstar asked 7 years ago
  • last active 7 years ago
0 votes
2k views

My washer wont spin out

0 votes
2k views

My Lg window air conditioner is leaking water.

0 votes
2k views

The customer had previous service for the ice maker freezing up and a new ice maker was installed by previous servicer. Based on customer complaint of needing to manually thaw the fill tube we replaced the water valve. Customer now reports continued icing up in the ice maker.

  • mbryan59 asked 6 years ago
  • last active 6 years ago
1 vote
3k views

Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.

  • dwoods asked 4 years ago
  • last active 4 years ago
0 votes
2k views

My icemaker is working, but it seems that some water is getting into it and causing all of the ice to freeze together.

  • Guye Y asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Does anyone have the diagnostic codes or troubleshooting information for this model ?

  • Dan Goodard asked 9 years ago
  • last active 9 years ago
0 votes
2k views

This unit has a door that’s not closing properly, and possibly a control issue. I explained to the customer that it could be either, but would a new door hinge really be the first route to go, or should I also order the control just in case? The door latches and isn’t leaking, but it doesn’t sit correctly.

0 votes
2k views

I’ve replaced the main board and heater already myself but must have done something wrong because the HE error code is still coming up. Did I get a bad heater? Or could there still be a different issue? Thanks for your help.

0 votes
31k views

Have LG refrigerator with ER 1F code. Fan motor for icemaker runs then shuts off.
Has anyone ran into this problem?

  • RANDOLF APPLIANCE SERVICE asked 9 years ago
  • last active 8 years ago
0 votes
2k views

My LG washer is very loud while in use.

0 votes
2k views

No heat.

0 votes
2k views

I have a washer that the drain pump will only come on for 3 seconds then shut off. Hoses are good and no obstructions. Everything else works normal except drain issue. Steve

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Any hints on where can get similar spring spreader tool like LG 383eer4004a? Thanks

  • Randy W asked 9 years ago
  • last active 9 years ago
0 votes
2k views

all the fans are working the compressor is running . no frost on evap coil and black soot on the inside walls of the fresh food compartment Checked evap coil no sign of burning wires or defective defrost heater and no sign of Freon leak The refrigerator is only 2 years old Would appreciate some help

  • raymond asked 7 years ago
  • last active 7 years ago
0 votes
2k views

My LG washer is noisy during use.

0 votes
864 views

Would like to know how to open the dryer to replace the rollers.

  • haivanpham asked 2 years ago
  • last active 2 years ago
0 votes
3k views

I have another one for you guys, this Washer is getting a drain hose error, but I’ve cleared it and can’t find the issue. Hooked it back up and did same thing.

0 votes
3k views

I’m almost positive this is a water valve but can’t find the schematic breakdown, anyone there have a minute to look it up for me? Thanks.

0 votes
2k views

Customer out of California is running across a lot of Samsung washers (top and front loaders) and getting a lot unbalanced loads and a lot of tubs bouncing around. Beyond overloading, is there any common problem we are seeing out there that is causing unbalanced loads and tubs to bounce around?

Thanks!

Showing 1 - 30 of 904 results