Brand: Whirlpool

see summary

Thanks

Al Zawalich

azawalich@hotmailcom

Have a whirlpool refrigerator model GI6FARXXY07
the evap motor is not running.

Complaint is the dryer is scorching the customers clothes. I found the manual in the library for the dryer but this problem is not addressed. I have not run into this issue before with a dryer and am looking for some advise on what to look for besides a clogged vent, drum seals, normal wear and tear. Could it be a bad cycling thermostat? Thank you for any advise. Thanks

—

This unit quit mid cycle and isn’t draining. What is the part information on a pump replacement?

This unit shuts down and turns off when it gets to the spin cycle but then will finish the cycle if the customer waits and let’s it cool down. Says it’s starts back up where it left off and then works fine. What should I take with me for this?

This washer won’t go through it’s proper cycles and sometimes even skips some and moves on to the next. Sometimes it’ll work perfectly fine and other times it’s just all over the place. Sounds like a control to me but wanted to run it by someone else first. Thanks.

There is ice build up in the bottom in the freezer section of my whirlpool refrigerator.

Ice maker is not working I have a reverse osmosis water filter , could this cause my issue ?

My Whirlpool dryer is not heating.

Push button for start broken out. Go to replace console and find once I remove the 2 circuit boards from the console that the start pad on user interface board is busted. Great, more issues. LOL
Trying to price out part, I run into a headache. Original part number is W10110658.
1. First parts house tells me special order. They check Whirlpool inventory and says they have 10 in stock. But customer doesn’t want to wait.
2. Second parts house says part number changes to W10294715. In stock. Something don’t seem right. Call 2 more parts houses.
3. Third parts house says part number now W10756696. Not in stock.
4. Fourth part house says part number is W10294708. In stock.

My Whirlpool dryer will not start and only makes a clicking noise.

My ice maker in my Whirlpool refrigerator is not making ice.

My Whirlpool washer is not filling with water, any suggestions?

I’ve replaced the IM 2 times and the motor module once. Freezer is normal after, for apprx. 4 – 8 mos., until customer again finds the freezer with “false frost” all over it(in the front, the back, top and bottom, the IM). It is almost everywhere! Problem does not appear to be air infiltration or evaporator not defrosting. Problem appears to be IM issue(as if IM has the heater staying on too long) Customer ready to replace refrig. Any service bulletins or suggestions on this? Thanks in advance for any help.

REAR WATER INLET TUBE FREEZES UP, THEN FREEZES RECEIVING CUP AND REAR END OF FREEZER. HAVE DEFROSTED AREA THEN GET ONE LOAD OF ICE, THEN IT FREEZES UP AGAIN.

The icemaker on this unit keeps freezing up and not rotating. Will work for about a month then freeze back up.

My Whirlpool dryer is not getting heat.

Range was converted to LP, now must be converted back to NG. Landlord changed regulator but that is all. Looks like the surface burners need NG orifices (not on unit). I find them in the parts listing.
I see there are LP orifices in parts listing for both bake and broil burners. I do not see NG orifices listed.
Does any know part numbers for the bake and broil burner orifices for NG? Thanks in advance

Hi Folks,
This unit contains a W10135090 Board which is replaced by a part number 2252189 but this replacement board is hard to come by. They just don’t have them in stock! Why I don’t know! The Repair Shack made a repair on the W10135090 and said it was good to go…Installed and still not cooling. But in the fresh food compartment controls if you install a bulb in to the top of socket near the Led the Led goes off. If you loosen the bulb the LED showing the temperature setting goes back on! Anyone have any ideas on this situation. All input greatly appreciated.

FRENCH DOOR UNIT WITH DUAL EVAPORATORS, THE FRESH FOOD SECTION IS FINE. THE ICE HAS MELTED IN THE DOOR, AND THE FREEZER SECTION HAS A LOT OF SOFT BUILT FROST ON IT. THE FAN SEEMED TO BE ACTING STRANGE CUTTING OFF AND ON. I CHECKED THE DEFROST T-STAT AND HEATER AND IT WAS GOOD. COULD THE FAN OR MAIN BOARD BE CAUSING THIS OVER FROSTING? AS I OPENED UP THE UNIT TO CHECK THE PARTS, THE COILS STARTED TO DEFROST. THE FREEZER WAS COOL BUT NOT COLD ENOUGH TO FREEZE EVERYTHING IN IT. I DON’T THINK IT’S A SEALED SYSTEM ISSUE, BECAUSE FRESH FOOD SECTION IS WORKING FINE, BUT I COULD BE WRONG.

Please help on error code F8E0

it’s says sensing and then I get the F-01