Brand: Whirlpool

I have a French door whirlpool fridge that the freezer is not cooling at all. Fresh food section is fine. There is no frost on the evaporator coil. Compressor is running to cool fresh food section.

My Whirlpool refrigerator is not cooling in the fresh food area.

My gas whirlpool dryer will not heat.

My Whirlpool washer will not spin out.

Whirlpool Cabrio Customer complaint it doesn’t complete spin cycle, water is pumped out but clothes are still wet. They start spin cycle to finish load.
Error codes:
F7E7 – Motor unable to reach target rpm
F0E2 – Over suds
F7E1 – Basket speed sensor fault
Unit agitates and spins in diagnostics. There is no clothes caught between tubs. There were no flashing lights when performing the tachometer verification mode. Wires and connections were good.
Not sure if this is a shifter problem or main pcb problem?

Already checked the belt, intact and not broken. Maybe the motor? Not sure where to start.

This washer won’t go through it’s proper cycles and sometimes even skips some and moves on to the next. Sometimes it’ll work perfectly fine and other times it’s just all over the place. Sounds like a control to me but wanted to run it by someone else first. Thanks.

This Whirlpool Cabrio Gas Dryer – – F-01 fault reads F-01. Runs, heats, but short cycles. Vent is clear, but still short heats cycle. All thermals and thermistor test good. F-01 states bad control board, but which one to replace;
Diagram shows two: this one – W10298628 and W10294316
I am thinking it is W10294316, but not sure.
Thanks in advance for any help

THANKS MATT. CAN A COMMERCIAL HEAT GUN BE USED TO SPEED UP THE PROCESS?

GOOD MORNING
REFRIGERATOR WAS TRANSPORTED LAYING ON ITS SIDE WITH DOOR TO THE PASENGER. PLACED IN HOME AND WAITED A DAY FOR EVERYTHING TO SETTLE. NOW IT WILL NOT COOL. I AM BEING TOLD THAT COMPRESSOR COMES ON. WHERE DO I START? THANKS, TODD FROM NY.

I am looking for fault or error codes for the model below. Thanks in advance for your help

I am looking for fault or error codes for the models below. Thanks in advance for your help

WRF989SDAB – Black
WRF989SDAE – Black with Silver Handle
WRF989SDAF – Mono Satina Steel
WRF989SDAH – White with Silver Handle
WRF989SDAM – Stainless Steel
WRF989SDAW – White

I have an under counter ice maker and it has good water pressure to the unit but will not produce any ice. Where do I start the diagnoses ?

I have a whirlpool electric dryer. I checked all components and found one needed a timer. Then I hooked up the dryer which I know was working before and it does not run. I check my power source and have 240 volts and 240v at the terminal block of the machine. I brought the dryer home and hooked it up at my house and it runs great. I don’t understand enough about loads. Why do I show 240v but the dryer will not run? How would you check this so you don’t make a mistake and think your power source is good? Thank you

Found a bad pump on this and am training someone, do you guys have a video I could use, nothing came up by model number. Want him to watch the repair and then try doing the install on his own. We do so many pumps, it’ll be a good way to start him off. I normally keep some machines around to do repair work on but am out of luck on this. Figured you guys would have something. Thanks a lot!

Indicator light stays on 24/7

Apparently this unit is out of warranty, but the customer stated they called whirlpool and that they are sending them the drain kit for us to replace. Have you guys been doing these? Wondered if I should be keeping an eye out for more.

Didn’t find a whole lot if info on this model. It’s not starting and keeps saying the door is open even when it is opened & closed repeatedly. Door is tight, seems to latch fine, the handle isn’t broken. Just won’t get going. Is this a magnetron issue or diode? I saw a lot of those repairs but am just not sure. I don’t work on these enough to know definitively. Appreciate the help.

This unit paused and quit right before the drain, but then proceeded to just slowly drain almost completely. Pump is fine, I did clear some debris from the sump area and spray arms, and ran it again to have the same issue. Disposal is clear, the punch is out, and didn’t find any obstructions from there. What am I missing?

This dryer is making a horrible screeching noise that I could hear over the phone. I’m taking an idler pulley with me but what are the drum supports availability? I’m thinking I’ll need both.

I have a customer with an electric whirlpool cabrio dryer a few years old, . After about 10 mins into the cycle the motor will turn off. And then after about another 5 mins, it will turn back on by itself. The display stays on, and counts down like it is running normally. The clothes do not dry due to this issue. the customer has had the vent cleaned so that is not the issue. The vent is about 10 feet all smooth 4″. Also it is not in the wrinkle prevent. That’s not the issue.
I have already replaced the thermal fuse and thermistor. And the main control board p#w10317636.
When i first looked at the dryer I disconnected the thermal fuse p#3392519 And hit the start button. And I heard the motor relay close. So power still goes to the motor, it just interrupts the circuit.
All I can think of is, the fuse, the belt switch or the motor its self. And from what I can remember if you open the door the motor relay shuts down. Also the touch pad p#W10269610 is a special order item. nonreturnable, 1-2 weeks to get.
Anybody help or insight into this problem would be greatly appreciated.

I have a stand alone ice maker with the square grid wires.The ice will not produce and drop into bin.

This unit shuts down and turns off when it gets to the spin cycle but then will finish the cycle if the customer waits and let’s it cool down. Says it’s starts back up where it left off and then works fine. What should I take with me for this?

I found the pressure hose that needs to be replaced. Part # I found is 353244. Is that right? Looking to head back out there tomorrow with it. Thanks.

Looking for the ignitor on this model

Do you guys have a video for this model?

Whirl Washer F11 code,
I already replaced MCU, checked wire connections at CCU and motor. Worked for 3 loads after replacing MCU.
What else is there to check?

Lid is locked and cannot get it to reset. Got there and found the drain pump seized and not working. Do you have this drain pump?

Need a man control on this washer. Getting an F1 and the door doesn’t always lock correctly. Do you guys carry it?

Is anyone else has issues with the Whirlpool Siphon Break kits that are currently available? The current part number is 76660. The internal parts of this siphon break don’t hold up very well and will actually pull out of place effectively blocking the drain port. We have always used the Maytag version of this product 201112 or later ones were 12001586 until they were discontinued. The internal parts of the Maytag siphon break are designed differently so they are much more durable and do not come apart. I have made some attempts to contact Whirlpool to see if they can redesign the Whirlpool siphon break so it doesn’t fail.