Brand: Whirlpool

I need part information on a new agitator for this washer. The customer tried to get it apart himself and I gotta replace it now. Thanks.

Water leaking on floor, is there a drain repair kit ?

This unit has Ice in the freezer floor and leaks water on the floor.

Got this dishwasher apart and realized I had pulled the wrong information for the motor and pump assembly. Is this something you guys have? Would be great if so. Needing to finish this up if it’s something I keep on my truck or maybe something I can pick up? Customer has a huge family dinner tonight for Mother’s Day and I need to get them up and running as soon as possible. Thanks you guys.

The door seal had a tiny gap near the bottom, that wouldn’t be enough to cause this issue would it?

what part number do I need to get this working again?

This unit quit mid cycle and isn’t draining. What is the part information on a pump replacement?

This is a washer that is continually having issues where it stops before certain cycles. Sometimes before the first drain, sometimes before spin, other time it won’t spin or drain at all. Customer said they can normally open it up, set it to where it needs to be manually and it’ll go again. What parts should I take with me before heading there? I’m hoping I have it already and can save us both an extra trip.

if the customer lifts the lid and closes it again it continues, sometimes. I’m assuming a lid switch for this?

I’ve checked all the main components and common issues, but think I’ve narrowed it down to the tco that neesd replaced. Possible? And do you carry it? Need to get this repair done. Thanks.

Per the customer he already replaced the icemaker and saddle valve himself but is still having issues. What else should I have on hand to get this fixed and working again for him? We don’t do many icemaker repairs and I’m trying to do him a favor by helping him out.

I’m pretty sure this will be the belt due to the customer’s description and finding pieces of rubber on the floor. Whats the part number for this?

The washer will without fail make it to the rinse everytime. The in use button is lit however the rinse isn’t, advancing one “tick” will put it in rinse but it does not fill, attempt to wash or advance from there. If you bypass the lid switch and advance it roughly 3 ticks it will start agitating without water or filling. If you advance it far enough (right before final spin) it will spin while adding water.

We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 mins. pause, drops to 5 mins on display, drains and spins, end of cycle.
There are NO fault codes showing or saved.The control was replaced about 1.5 years ago. The unit ran fine after the board replacement.

We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 minutes. pause, drops to 5 minutes on display, drains and spins, end of cycle. There are NO fault codes showing or saved. The control was replaced about a year ago. The unit ran fine after the board replacement. This unit is located in a beach house and gets only a few months of use a year. Any help or advice would be greatly appreciated.

Would I need to replace more than just the element here?

The brand is Whirlpool it wouldn’t let me enter it.
I am working on this refrigerator and water is freezing and leaking out of the ice maker compartment. Any ideas where it is coming from?

Water is running down inside the refrigerator and accumulating under the drawers. Seems to be cooling ok right now but am assuming it will have issues eventually at the rate the water is backing up. Can I just clear the drain and call it good? Or should I be taking a more “look ahead” option to this if it keeps happening? What’s a permanent fix?

Need a new pump for this unit, and don’t have the part information. Do you also have any videos on this? Trying to train one of our new guys on some basics. Thanks.

Looks like I need a new idler, but can’t find the part number for this model. What do you guys have?

Complaint is the dryer is scorching the customers clothes. I found the manual in the library for the dryer but this problem is not addressed. I have not run into this issue before with a dryer and am looking for some advise on what to look for besides a clogged vent, drum seals, normal wear and tear. Could it be a bad cycling thermostat? Thank you for any advise. Thanks

—

Timer motor will run to cool down part of cycle but won’t advance to off. The dryer ran from 10pm to 4am on cool down,

I have need of the part number for the small fuse link that is on the back wire to the control. It has Two fairly large spade terminals at either end. I cannot see it listed on the schematic. Can anyone assist?

This microwave has a stuck or defective power selector button on the keypad but Whirlpool does not supply any parts for it other than the turntable components.
I’ve checked several sources and they all show the turntable components as the only available parts.
Unit three years old and parts obsolete!

Timer on dryer was not advancing. Changed timer and it also is not advancing. What could be the cause of this. Thanks for your comments.

I am working on a Whirlpool WFW8400TW02. HLW 19 Initially I found long drain errors stored and the pump not running looking for power to it I found open neutral feed diagnosed CCU failure pump ohm’s 14 door also locked. Replaced ccu door remains locked no errors pump ran breifly with new ccu unplugged mi3 connector still no errors shown door locks no motor function throughout after , I replaced two ccu boards still same has anyone seen this?
Lock ohm’s 60 both ways
Interlock SW is closed
Pump 13 ohms
Polarity correct
Any suggestions would be greatly appreciated

We have a different problem with this washer
According the customer explanation it happens once in 6-7 cycles.
At 26 minutes before the cycle ends display shows code UL(unbalance load),
but the unit is still running ,the customer hears some loud clicks,at the same time unit
starts filling with water ,it fills over the edge of the tub .
If you press “Stop”,to continue the cycle after that you have to choose “Rinse and Spin”
only .If anyone has an experience with this problem please let me know .
Thank you very much in advance