0
0

I cannot get any pads to work to enter code

Model Number
GI5FSAXVY02
What have you tried so far?

I replaced main board, because all was dead. compressor, light on display etc. when I replace board all worked but I cannot get the front display to program. cannot get pe0000 off I went through programing or tried to. no matter what I pressed would not change If the lv board behind keypad is defective is it available?

Request Resource Materials
Service diagnostics guide, Service bulletins, Videos, Any available materials
0
0

Hi. I have attached a video for you on how to enter the program code. I hope this helps. It is on a similar model. Start at 5:00 mins on the video.

0
0

Hello
It sounds like your entering in the wrong programing code. The Program Code is located on the Serial Plate on this unit after the word Code. If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a Program …CODE of PE0000 will show ).Once the correct Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect this process should be repeated.
The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds or will exit if unattended for four minutes.

Control board Troubleshooting
Programming Mode:
NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.
1. Press and hold the Door Alarm Keypad.
2. Press and hold Freezer Temperature DOWN /- Keypad within 3 seconds.
3. Release the Door Alarm Keypad and wait 3 seconds.
4. The control will display PE to indicate the programming mode.
5. Entry is confirmed by pressing the Freezer Temperature DOWN /- Keypad once more.
6. The control will display the current Program CODE. This value should be validated with theProgram CODE printed on the unit serial plate.
NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.
7. Press the Refrigerator Temperature UP /+ Keypad or Refrigerator Temperature DOWN /- Keypad to change the digit value with each key press.
8. The decimal point indicates the selected digit. Press the Freezer Temperature UP /+ Keypad to select the next digit.
9. Once the desired Program CODE is entered, press and hold the Freezer Temperature DOWN /- Keypad until the Program CODE begins flashing
indicating it has been saved.
NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a Program
CODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect this
process should be repeated.
The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds or will exit if unattended for four minutes.

Service Test Mode:
The service test functions are performed using the refrigerator display and keypad. Enter the Service Test Mode by performing the following sequence
of events:
1. Press and hold the Door Alarm Keypad.
2. Press and hold Refrigerator Temperature UP / + Keypad.
3. Release the Door Alarm Keypad and wait 3 seconds.
4. The Freezer display will display SE confirming entry in the Service Mode.
5. Press the Refrigerator Temperature UP /+ Keypad again to confirm entry in the Service Mode.
6. Display will show 101 in left display and numeric or dashes in right display.
7. Press Freezer Refrigerator Temperature UP / + Keypad and Freezer DOWN /- Keypad to toggle through Service Test numbers.
8. To exit service test mode, open and close refrigerator door or hold door alarm for 3 seconds

    • Guest
    • 7 years ago
    I can press any pad nothing will change. it will not except programing mode . I have been through programing mode several times. I go through the steps just as outline cannot enter a thing. I can press fresh food temp up and the right two digits flash ice press down temp I get H2o and that’s it!
Showing 2 results
Your Answer

Please first to submit.