All Answers

This could be an issue with the evaporator cover assembly. Here is the part number AEB73944701. Below is a link to the repair video.

This sounds like an issue with the door mullion. Here is the part number for the mullion AGU73530705. Below is a link to the replacement video.

This sounds like an issue with the auger motor. Here is the part number for the motor. EAU60784228. Below is a link to the auger motor repair video.

The issue could be with the water tank. Here is the part number for the tank. AJL72911502. Below is a link for the water tank repair video.

Hello
See the video link below on how to remove cover. Then go to section 1-15 in the service manual link below to do your voltage checks . One you have done your voltage checks, go to section 3-1 for component testing to determine what component is causing your issue.

Hello
There are many possibilities for your symptom. You will need to run the unit through the load test mode on page #16 in the service manual link below. This will run run the unit through diagnostics and give you the troubleshooting recommendations on what part is needed. On pages #40 through #45 are the complete parts breakdown of this washer / dryer. I have also added a link to a washer/ dryer combo WM3488HW that has 22 videos. It is very similar to your unit.

Hello
See page #44 for proper seal installation. Here are some other possibilities for your issue.
1) Make sure you are using proper dishwasher detergent. Any other types of soap may cause sudsing inside the dishwasher, resulting in poor wash performance and possibly suds and water on your kitchen floor.It is important to use high quality detergents, such as Cascade® Platinum™ Automatic Dishwashing Detergent.
2) If the upper wash arm is cracked, it can force water to spray directly toward the dishwasher door seal, causing a leak. Remove the wash arm and inspect it for cracks. If the wash arm is cracked, replace it. These waves can cause water to leak out of the bottom of the door.
3) Sometimes food particles, soap residue, and other debris can cause clogs that prevent water from draining. A clogged drain can lead to puddling inside the dishwasher that eventually leaks out the bottom of the door.
4) Make sure the unit is properly leveled.

I recommend replacing the secondary water Inlet valve. Here is the part number for the valve. MJX41869202. Below is a link to the repair video for the valve. MJX41869202

I recommend replacing the ice maker assembly. Here is the part number. AEQ72910411 Below is a link to the repair video for the ice maker assembly

This issue is usually occurs when the door gasket is damaged. I recommend replacing the gasket. Here is the part number for the gasket. ADX73550624. Below is a link to the repair video for the gasket.

This issue is most likely caused by a bad water inlet valve. Here is the part number for the valve. MJX41869202. Below is a link to the repair video for the inlet valve.

Hello
Ge to page # 16 in the manual link below and go through the troubleshooting guide on no agitation. This will take you step by step through the diagnostics.

Hello
Here is the service manual and there is one service bulletin . Yes, it could be a stuck touch pad. I would advise to shut the power down to the unit for five minutes to see if the board will rest. Then run the unit through diagnostics per technician sheet link below.

Hello
We do not have the exact manual . I found a manual close to your model Service manual #795.51373. This may help, test mode is on page #97. I will email web developer not to charge you for this question since its not the exact manual.

Hi, I have attached the tech sheet for you. Even though you ran the unit on cold water, it could still bring in some hot water to reach the correct temp the machine thinks cold should be. This may have cause the error. Make sure both hot and cold are hooked up and working. Run through the steps for the error code in the tech sheet Run diagnostics to see if you can find a failure. You tried blowing through which end of the drain hose? Is the unit not draining? Make sure the pressure hose is clear.

Hello
See the 131 page service manual link below. This will give you all the troubleshooting ,diagnostics and access for your #sdgt09 Model.

Hello
The 8C2 error error could have a few possibilities. See the complete diagnostics in the manual links below.
1) Possible defective Mems PBA .
2) A possible PBA wire disconnection.

Hi. Did the tech say why the door needed to be replaced? A broken damaged wire in the door should be the only reason to replace the door that I can think of. I am not finding much info about this issue for this model. I did come across a couple of people with similar models that had broken wires where the wires enter the door through the hinge and another with a loose connector in the same location. I have seen faulty control boards on other brands and models with the same issue. If I recall right, I may have had a bad user interface for one as well. I would have to say wiring or the control board would be the most likely issue. I hope this helps.

Hello
See the compressor diagnostics link below. It will take you step by step through the compressor diagnostics.