1 vote
3k views

Compressor won’t run. No power to compressor.Do you think the computer board is bad or the thermostat dial control?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

The thermostat seem to check out good.The fans in the fridge and freezer are blowing I cannot tell if the compressor goes on or not. What might I check to see if one of the other switches is bad. I don’t know if it is whirlpool or frigidaire. It is a sears coldspot.

  • Garold Jang asked 10 years ago
  • last active 10 years ago
0 votes
3k views

The entire touch pad works except for Bake, Broil, and convection. All the digits and timers clock keep warm, pizza, the rest of the key pad functions. Tried to reset by unplugging. Didn’t work. Oven comes on by using the pizza function. Top burners work as well. Why only a few not work?

  • Ronda asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Wiring diagram needed for Frigidaire dual range Model# PLCF489ACB
I am having the board rebuilt by CoreCentric and would like to have the wiring diagram to make sure everything is wired correctly. I am not the first to work on this. Any help is greatly appreciated.I would try looking for a video at ApplianceVideo.com. Just type in your symptom and look for a free video.

0 votes
3k views

I have a frigidaire dryer that no longer heats, my clothes are still wet inside after two cycles. I had a hard time finding the correct replacement part online and there wasn’t a video I could find for my model. Hoping someone can help!

  • Rebecca Nolan asked 9 years ago
  • last active 9 years ago
0 votes
3k views

So I changed the coils and the igniter and the senser.
The falme still will go on for 5 to ten seconds and then go off.
And will repeat about 1 minute later
I have have taken the vent off of the back and no difference

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My Frigidaire washer is not draining.

0 votes
3k views

Can somebody get me the part number for gas coils for my dryer? It isn’t heating up anymore. My son is going to come fix this for me and I can’t find the number. I keep telling him it’s an easy fix and if I can get him here I want to make sure I have the part he needs to get it working again. Can’t have him yelling at me for not at least doing that. And thank you.

  • Ken Gannon asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I replaced a broken door latch & striker and am still getting a drain issue on this. Pump is fine, checked drain hose, and control checks out. What am I missing?

0 votes
3k views

My dispenser does not dispense any water or Ice. Although if I initiate the dispenser at the same time pull down with my index finger to initiate the movement , It does work. The other part is, If I loosen the screws holding the assembly in place and Pull it toward me just a little it also works. Very strange. I’m missing something, Just don’t know what it is…Can you help

  • Bob Henderson asked 10 years ago
  • last active 10 years ago
1 vote
3k views

I’ve been noticing ice buildup in our freezer, and water gathering on the shelves in the refrigerator. Where is this water coming from?

  • Darren Boyles asked 10 years ago
  • last active 10 years ago
1 vote
3k views

The water supply is good. The voltage to the primary valve at the brown harness is only 66vac. Isn’t it supposed to be 120vac? The voltage to the dispenser silnoid it 120. I tested the triac at the brown harness tan/yellow and the blue harness at the yellow and blew and it checks good. Is that a proper way to test it? Does the voltage supply come through the main power board? If so then is it the problem? Any advice?

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views

My Frigidaire Professional FPHD2491KF buttons don’t work. Well only two light up when I press them. The start button does not work so I can’t run the machine. Would that be a console assembly problem or a pc board problem? How would I find out which one needs to be replaced as I have searched many forums and websites indicating that it can be either the PC board or the Consol assembly (panel where you press buttons) Thanks!

  • Pedro asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Hi, I would like to follow the repair instructions from this video: https://www.youtube.com/watch?v=k1KEfcNfcMo

But I do not know which tools to purchase, could you tell me the name of the tools used?

Thank you!

  • Julianne asked 9 years ago
  • last active 9 years ago
0 votes
3k views
  • Jim Weaver asked 9 years ago
  • last active 9 years ago
0 votes
3k views

We went out to change the dispenser paddle on a frigidaire refrigerator. After changing it out the auger motor continuously ran. disconnected micro switch for paddles and auger motor still continuously ran. Changed out power board, still the same problem. Changed out user interface board. Still the same problem. Also Ohmed out wires inside door for possible short. This did not do this till I changed the paddles. Anyone have a direction to go in ? Thanks

0 votes
3k views

I would like to know if all these refrigerators are setup to accept ice makers or do I have to drill holes?

  • Gary Grzechowiak asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Recently, we experienced some frost buildup on the door of the freezer as the door did not close completely. Soon after that incident, our icemaker has not worked correctly.
It is not producing ice.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I HAVE NO POWER TO THE WATER CONTROLS ON THE DOOR AND THE EVAPERATOR FAN IS NOT WORKING. REFRIGERATOR BEEPS EVERY FEW MINUTES

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

My washer wasn’t spinning so I took off the cover and found a broken belt down underneath. I couldn’t find a video with the part number or model and need a little help in figuring out how to install the new one.

  • Roy M. asked 9 years ago
  • last active 9 years ago
0 votes
3k views

washer not running will not enter diagnostics, beeps three times with new board, nothing else

  • Guest asked 6 years ago
  • last active 6 years ago
0 votes
3k views
  • derrick asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Serial: 4A43011509

Ice clumps in ice bucket every 3 days.

Brand New SxS Frigidaire fridge. No leaks from ice maker. Zero degrees in Freezer with good evaporator fan airflow. Ice dispenser Door and Freezer door close nicely. I thought maybe the icemaker heater was sticking on so I replaced ice maker with now improvement. Within a couple days they call back and all the ice cubes are frozen together. Any Ideas would be greatly appreciated.

0 votes
3k views
e51

so im getting a E51 error and the customer state that the dryer keeps on running

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I haven’t had a chance to physically diagnose this but want to take something with me since the customers requested the work be done asap for the holiday. I think it’s the console assembly but wanted to verify with you guys.

0 votes
3k views

I’m getting an error code on my oven display that I looked up and it says it’s for the probe? But my husband checked it and it is working properly. So what do we do now? I don’t want to replace it anyway if it’s fine.

  • Brittany H asked 9 years ago
  • last active 9 years ago
0 votes
3k views

evaporator motor was replaced the adc electronic board was replaced and the damper assembly was replaced and frigde is still not getting cold it’s cool, not cold enough
please help

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

THE UNIT IS COOLING WELL BUT I HAVE NO DISPALY ON THE FREEZER DOOR. NO LIGHTS NOTHING.
I NEED TO TRACE CIRCUIT BACK TO SEE IF OR WHERE I’M LOSING POWER. ANY INFO ON BOARD TEST POINTS ETC.

TX

  • Guest asked 7 years ago
  • last active 7 years ago
Showing 31 - 60 of 395 results