0 votes
1k views

Attempted reset that LG manual showed to do, with no change. Tested breaker and have proper power to terminal block on dryer. No light in tub area so can’t check door switch. What can I or do I attempt to check next?

  • Guest asked 3 years ago
  • last active 3 years ago
0 votes
704 views

My washer is showing “DE ERROR CODE”

0 votes
749 views

My LG washer is showing an PF error code.

0 votes
734 views

My LG washer will not fill with water.

0 votes
758 views

I have an LG french door refrigerator, with a automatic doors and drawers function. It’s activated by the foot sensor. I’ve checked the sensor for resistance as well as the connectors. all showed me some omes. Also, the auto drawers function is not working either when turned on. What could be the problem?

  • Guest asked 3 years ago
  • last active 3 years ago
0 votes
738 views

My LG washer is making a loud grinding noise.

0 votes
690 views

My LG washer is giving me a “UE ERROR CODE”

0 votes
733 views

My dryer is not heating up at all.

0 votes
790 views

There is water leaking from the back of the refrigerator.

0 votes
851 views

Ther freezer section is not cooling properly in my LG refrigerator.

0 votes
721 views

The door is not closing properly on my LG refrigerator.

0 votes
736 views

My LG refrigerator is making a grinding noise when dispensing ice.

0 votes
820 views

I am not getting any water out of my LG refrigerator.

0 votes
940 views

Hey I have a all in one washer dyer combo that is not drying the clothes. I replaced the drain pump and cold water inlet valve (all four). The clothes come out hot but soaking wet. The dyer works by putting hot air in the drum then running that hot air over an evaporation coil to remove the moisture. Then that water is drained. Then it puts more hot water in the drum again and starts the process over. Can you give me a parts list of possible bad components to try switching out sorted most likely to least likely?

  • Guest asked 3 years ago
  • last active 3 years ago
0 votes
842 views

The water pressure on my refrigerator is very low.

0 votes
808 views

My LG refrigerator is not making ice.

0 votes
858 views

There is frost building up inside my LG refrigerator.

0 votes
721 views

My LG refrigerator is leaking water.

0 votes
812 views

My LG refrigerator is not cooling in the freezer section

0 votes
907 views

My LG refrigerator will not cool in the freezer section.

0 votes
813 views

My GE refrigerator will not turn on or do anything at all.

0 votes
716 views
  • Guest asked 4 years ago
  • last active 4 years ago
0 votes
1k views

My lg refrigerator is not cooling nor freezing. I already check the deforst heater and the ohms are correct for both the freezer and the fresh food area. I havent been able to check the defrost sensor because not sure which reading i am looking for. I also need help to check the compressor.

  • Guest asked 4 years ago
  • last active 4 years ago
0 votes
1k views

Hello, the dishwasher is leaking during cycle on the bottom left side of door, there is a small black plastic flap? About 6 inches in length is the location where it drips from.
I don’t know if the leak is relative, but my dishes aren’t drying either, there is still water on dishes and such after the “Quick and Dry” cycle has completed???

  • Guest asked 4 years ago
  • last active 4 years ago
1 vote
2k views

So I have this LG French door refrigerator. After a filter change it stopped getting cold enough to freeze and the refrigerator isn’t getting as cold as it’s set to. The freezer is getting to 48 degrees, the refrigerator is getting to pretty much the same, so something is working.

Take the lower cover off and clean up the coils and fan. I bumped the drain tube and it started spewing water out of the top. Let it finish draining, took the tube off and found a glob of something in there, so it was likely blocked (it was building up ice on the inside of the freezer that would have to be cleaned out from time to time). Hoped that would be the extent of things. Ran for about a day with no change.

Took the electronics cover off, the boards looked good as in no burnt stuff, fuses intact. Ran the first stage of the diagnostics and the display lit up everything. Fan running, I believe the compressor was running. Hard to tell with these linear condensers. It had a slight vibration to it. Second stage of the diagnostics, gave a 22 code on the front. Went to stage 3, fan and I’m guessing the compressor shut off like it was supposed to. Great. Reset everything and it comes back to life, fan running and slight vibration to the compressor. I will note the compressor did get warmer and i could feel a bit of cold in the copper.

After looking up the code and doing some research I’m thinking ok this is cake. So I take the lower panel back off and go to look at what I’m dealing with before I buy parts. well this model does NOT have a compressor relay. It’s got a compressor wire harness. @#%$@@%#$%^%

How do I fix an error 22 on this? or is the compressor junk?

  • Guest asked 4 years ago
  • last active 4 years ago
0 votes
1k views

Not spinning fast enough at full speed on spin cycle, seems to drain fine, clothes come out soaking wet

  • Guest asked 4 years ago
  • last active 4 years ago
1 vote
3k views

Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.

  • dwoods asked 4 years ago
  • last active 4 years ago
1 vote
998 views

It will take as long as 4 to 5 minutes to come back on when (on the dual burner position) you go from low to high.

Is there an adjustment that can be made or is this a problem with the board? Which one?

Can you offer any advice? How do I test this kind of burner regulating system?

  • Guest asked 4 years ago
  • last active 4 years ago
0 votes
1k views

Eight months ago it did the same thing. Then it displayed ErFs shorted or disconnected freezer sensor . I chocked the ohms. There was some variation. I changed the sensor and it worked for 8 months.
Then it reoccured. They lost everything in the freezer but said the refrigerator section was ok. Then it worked fine for several days then both sections failed and lost All their food.
I just checked it for error codes and it showed NONE.
Is there no end to these kinds of situations?????
What do you all do in these situations. I know you must face them almost daily. You can’t just throw parts at it.
Are there any service bulletins for this. Any video’s or technical training that can help now and in the future???

  • Guest asked 4 years ago
  • last active 4 years ago
0 votes
1k views

very noisy on spin , need tare down vidio to replace bearings and seal .

  • Guest asked 4 years ago
  • last active 4 years ago
Showing 61 - 90 of 905 results