Brand: Maytag

keeps blowing fuses

I am looking for a way to access my drain pump as I’m getting error code E01 & F09. I see one of your videos that shows removing the kick panel to get to the pump but my washer doesn’t have a kick panel, it has an entire front face panel.

We have had our Maytag dishwasher for a few years. The door will not open. The latch seems lose and it you try to open it, the latch get pushed up and jammed. Is there a way to open the door so I can check the latch?

My washing machine fills up but doesn’t actually start. I came down hours later to find it had never began the load I put in. I was able to restart it and it worked all day yesterday. Just came down to find the same thing today. Why would it work sometimes and not others?

I have a couple elements that have gone out on my stove. Is this pretty easy to do myself if I buy the parts? Don’t want to put a lot of money into this thing cause we’re moving soon. Couldn’t find a video so hoping somebody there can.

maytag epic front loading washer will not spin on high. door knock works. drains fine. spins but never goes into high spin.

Can I turn my freezer to power 0 and leave the refrigerator part on in order to thaw out the frozen drain line and pan? Hopefully that way I don’t have to remove all the parts like in the video.

The dryer is not producing heat. I took the heating element out and the coil doesn’t seem broke anywhere. Should I still replace it or is something else causing the problem?

Thank you
Dustin

We had it stacked at our old place, and it’s been in storage for about a year. We unloaded them here and put them on individual pedestals since we have the room but it seems to not even want to stay on it’s stand. I’m afraid it’ll come right off one of these times on a spin cycle. Any advice for us?

I just changed both hinges on the oven door but there is still a fill finger gap between the door and oven on the left (when facing the oven) side of the door and you can fee much more heat there than on the right side. Wonder what other issues this could be? I have a new gasket as well. Could the door be warped? Thanks!

washer vibrates badly and walks across the floor. Washer is
level, floor is solid and all suspension springs are good. I noticed
that the tub is rather stiff, by that I mean when I pull or push it one
way or the other it will stay wherever I put it and will stay there even
when spinning. Any suggestion on how to fix the problem will be
appreciated. Thank you.

In the bottom oven the bake element doesn’t glow, it heats slightly though. The element itself tested good. As it is trying to heat a clicking noise comes from the back. Could this be the thermostat or something in the control panel?

I have a customer with a Maytag Gas Range, MGR7775WS 2, R10414233. This unit doesn’t have an ignitor but has a spark mule for the lower oven and it doesn’t always light on the first try. Is this something to worry about and is there anything that can be done about it?

Hello I am looking for the timer ,part#308222
It is a Maytag dryer ,mod.#LDG7400AAW
The part is NLA any suggestions ?

my refrigerator isn’t working not cooling in the freezer isn’t freezing anything you can hear the noise like it’s working but is not doing a thing

Maytag Neptune washer model# MAH4000AWW – starts and stops:
This unit has a timer and a motor control board and a push start button. When you place the timer on any load size and press the start button, the washer begins and fills with water. Once filed the unit shuts off. It does not advance, the timer is not ticking like any egg timer or moving through the cycle at all. If you press the on/off button again it will fill with a little water but stops and turns off.
The motor control board and the time are both expensive. Too expensive to replace both, but i am having trouble separating out which one it may be. I am not looking to the motor because the timer is not advancing at all or should it be, I am not sure.

making load noise during high spin

MY WASHER FILL BUT DON’T WASH FILL LIGHT COME ON NO MOVEMENT OF AGITATION. WHEN PUT ON DRAIN AND SPIN IT’S WORK (DRIVE MOTOR DUMP MOTOR WORK DRUM SPINS.)

MY WASHER FILL BUT DON’T WASH FILL LIGHT COME ON NO MOVEMENT OF AGITATION. WHEN PUT ON DRAIN AND SPIN IT’S WORK (DRIVE MOTOR DUMP MOTOR WORK DRUM SPINS.)

CHANGE HV BOARD, DISPLAY BOARD AND TOUCHPAD NO RESPONSE REFRIGERATOR HAS IN LIGHTS BUT DOESN’T WORKS

it’s really loud on spin and I’m wondering if you guys do this repair a lot or if it’s worth it? Not sure if I should just buy new or not at this point?

Ice maker is only crushing ice. The solenoid is not activating so the dispenser arm is not allowing cubes to dispense. I changed the solenoid, which was visually damaged on the inside, but it is still not activating. Would this be a Maytag Refrigerator Dispenser Actuator, part #W10205979, problem? The auger is working fine, it spins when the ice dispense pad is pushed.

My compressor is making noise, I like to look into it but need to remove the freeze bins (top and bottom) to get to it. I’m having trouble with the removing the bins. I was able to remove the door on the freezer, but I’m stuck on removing the bins. Seems like there are 2 tabs on the top bin that’s blocking the top bin from sliding all the way out. Is there a way to remove the blockers? Am I suppose to remove the top bin first then the bottom bin? Let me know if I’m going at it the right way.
Thanks,
-Frank

machine started popping while on spin cycle. It will not spin at full speed. Clothes are soaked. I installed a new thrust bearing kit part number 2100 1734. It will not go into proper alignment with the shims. With the small shim. 032 thickness it is below the minimum pulley hub reference. I removed all the shims and it is aligned perfectly between the two marks.I tried it again and it is spinning at full speed but then pops again and slows then goes back to full speed then pops and slows.it is a little better but it is still not right. I’m starting to wonder if its the transmission. Any help would be appreciated I’m about to just throw it out the back door and go buy a new one.thanks.

I am a servicer. I think this is an auger related issue. What steps should I take to trouble shoot to diagnose the related switches and circuits related to this problem?

Maytag Neptune washer model# MAH4000AWW – starts and stops:
This unit has a timer and a motor control board and a push start button. When you place the timer on any load size and press the start button, the washer begins and fills with water. Once filed the unit shuts off. It does not advance, the timer is not ticking like any egg timer or moving through the cycle at all. If you press the on/off button again it will fill with a little water but stops and turns off.
The motor control board and the time are both expensive. Too expensive to replace both, but i am having trouble separating out which one it may be. I am not looking to the motor because the timer is not advancing at all or should it be, I am not sure.

WHAT IS IT AND HOW TO REPAIR IT?