Brand: Maytag

Put it in diagnostic mode C00. Doors locks but do not hear pump starts and it just stay in that mode a period of time. Pump checks ok. I have it in different test phases at one time, such as C02 and C03 and worked, but only one time. Some of other symptoms are the CCU cycle power 120V out at MS2 output to the 120V input to MCU, stays on for 2-3secs.but drum do not attempt to turn..This symptom starts at odd times when you think it shouldn’t be happening. Some fault and error codes were F06 E01, F06 E02
Some questions I have. How long does a test phase should last. Such as C00.

During the rinse & spin cycle the agitator spins wildly and makes an insanely loud screeching/grinding sound while whipping the clothes so hard and fast they stretch and if caught right, will rip. If I cancel the cycle and select “rinse and spin” it will rinse the clothes, but then during the spin cycle the malfunction will occur again. I then tried a “drain and spin” cycle which seemed to operate normally.

I need to diagnose the issue and identify the right part to replace.

Thank you in advance for your help!

I have videos if you need them.

This is a Maytag Bravos MCT

Why won’t the service mode work? Is there a “trick” to it? Could a thermister cause this? If so which one and where is it located.

Any ideas? I watched the videos on the service mode and seems I am doing it correct.

Temp in freezer ok. Fridge stays at 28 degrees when set where it should be. Freezing food.

I put this unit into forces defrost and the compressor shuts off but the heating element never turns on. Checked continuity on the heating element and the bi metal. Both are within spec. I replaced the jazz board and it still does the exact same thing. I’m not sure if I could have gotten another bad board that does the exact same thing or am I missing something. The unit does go into forced defrost and everything shuts down as it should.

This washer appears to be one piece RE: the control top / front-sides. How do I remove the outer skin/frame to access the tub / seal?

My ice maker is not working. No water is getting into the tray to make cubes. I have left it for 24 hours, still no ice.

I have a Maytag bravo dryer and the f01 code is showing and it wont start.

Getting error code e01 f01. Spin won’t start after sensing or maybe very short and slow spin. Did spin once very fast and only way to stop was unplug. Have unplugged for 10 minutes to try for reset and problem still there.

Hello control panel lights up but start button not engaging. Possibly just a door switch?

Hi Maytag dishwasher control panel is not working. Can I reset?

Code f28 on control panel

Code f28 on control panel

My washer is not spinning properly and I’m wondering if I have a faulty relay in the control panel. In manual mode, the spin test (high and low) was not working. This led me to replace the motor capacitor. The motor capacitor was replaced, but now the spin tests time out after 5 or 10 seconds. Do I have a bad sensor or a bad relay? And would a replacement of the control board panel be in order?

It has power the drum will not spin

It has power the drum will not spin

MAH8700AWW Maytag washer. It does not spin, although I hear the motor running. No error codes. The timer in spin test does not wind down either.

MAH8700AWW Maytag washer. It does not spin, although I hear the motor running. No error codes. The timer in spin test does not wind down either

Ran service test. No error code. Just FE, Doesn’t have reversed polarity, amp draw on motor while running is good. Stops right at 15 minutes. So I replaced PCB, still doing the same thing.

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem

My Maytag Series 3000 Washer keeps displaying error F21. I’ve cleaned the long drain behind the bottom front panel and also checked all the hoses and none of which are kinked or clogged. The washer will complete all cycles and drain like normal when empty, but will display F21 when filled with clothes. I’ve put a very small load in (2 shirts and a pair of jeans) to make sure it was draining properly and am still getting error F21. Help!

Washer making a loud surging rubbing noise on the spin cycle.

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem. I have tried to unplug the unit to reset the board and it did not work.

Maytag MF12568AES refrigerator control panel not working. Yesterday came home and lights on control panel were out and it was just buzzing. I believe the fridge is working. We have had issue for past year with switching from water and ice so we have just left it on water. Which should I replace – control panel on back, control panel on front, or display panel. How can test to figure out which is bad. I unplugged the connector with three wires attached to control panel on the front and it lights up as normal but no water and cannot use any of the buttons.

My washer is showing code F3 E1. I had a serviceman out less than 6 months ago for the same problem. What he replaced was I think the drum motor. I had already looked the code up and saw that it was a pressure switch but he said he didn’t think that was it. At any rate, how can I get the door to unlock? I need to get the clothes out, obviously. He will be back on Wednesday to repair again.

My Maytag washer is very loud during spin.

My Maytag Neptune washer displayed a message that a key may be stuck. I was able to turn it off. But when I turned it back on non of the keys repond.