Brand: Samsung

The ice maker control says “lock” and can’t get ice.

i have customer who have Samsung induction range, and they got error E-84. keypad is not responding, i check the all control board and non of them have burning sign, i am planning to change touch pcb both side control board, i also download service manual and it says either invertor board or touch pcb board. how i can check inverter board without doing so much disassemble cook top remove. give me good plan to check

My Samsung microwave is showing an e83 filter code how do I fix it?

I’m getting 7E error and grinding noises at certain points. It used to wash for a while, then stop with the 7E error. I checked that the water wall part that moves was attached properly and oriented correctly. Ultimately, I replaced the motor/sensor assembly. Now, when I start it, the water wall cycles back and forth, making a grinding sound when it gets all the way to the back (I think) and then displays 7E before even starting to fill. I can’t find anything binding. I removed the water wall track and it moved smoothly. I saw people on the internet saying that there is a problem with a magnet getting weak from the heat and no longer activating the sensor at the end of its travel. Could this be my issue? How to resolve?

how to replace de31-00070b on this range
please help

After defrosting the evaporator I tested the sensor it worked fine. Not sure about the heater. I got a resistance reading of 101.8 ohms though. the heater and bimetal. Can you get me a tech sheet with the resistance value on the defrost heater?

My client said it was cold and twenty-four hours later it was warm. When I check on it I found the evap and condenser fans running but not the compressor. I checked the overload and it was good, and there was 120v present at overload, did not find any voltage between any of the three wires that go to black plug that makes up to compressor terminals -wires are black, blue and purple. I suspect the inverter PCB is failed and wondered what you thought? Thank you.

This is a side-by-side Samsung refrigerator where neither fan is currently operating both bottoms are called in the coils are getting cold but me there fan is operated I tried installing a 2500 rpm Samsung refrigerator fan and also did not operate could this be caused by a faulty control board possibly I am trying to repair this for my Customer asap because Christmas is around the corner.

Note
Fan in fridge not working. Fan in freezer not working. Compressor fan is operating

Samsung refrigerator the flex zone dwarer wire harness is popping out of the side rail. This is causing the door not to close correctly. Also need the part number for that wire harness.

I have a Samsung Refrigerator w/Ice Maker; the ice maker continuously freezes up; I have searched online and it seems to be an endemic problem; any fixes out there or do I need a hair dryer in the kitchen?

Samsung ice maker ntgt001ta1 fills with water, frezzes but will not dump

My samsung washer says it is off kilter in the last spin and when I try rearrange the clothing, it returns to 17 minutes and then does the same thing when it reaches 5 or 6 minutes to go.

Samsung RF260DEAEBC French door with out Ice maker in door. Ice maker is located in the freezer. How do I adjust the cube size?

My Samsung RF267AERS ice maker is not making ice. I’m not sure if I should replace the ice maker or the water value. I do receive water thru the dispenser on the door. Thanks

Fresh food section / refrigerator Is not defrosting and restricting the airflow with the giant block of snow. Ran the system through self diagnostic mode nothing came up but when I ran the sensor diagnostic out of the ten sensors it tested, sensor #7 failed.
Now here’s the issue, the whole system is a cluster of bunch of plastic parts
IS THERE A MAP OF THE TEMPETURE SENSORS so I can find #7 instead of finding all 10 and having to test manually?

(In Samsung category because wouldn’t find GE brand and unit compressor was Samsung)

will not go into spin cycle.

Everything I can actaully get it to go thru entire quick wash by allowing the hose to drain with lowering it to floor. It gets stopped on each part of cycle where it needs to drain so i lower hiose to plastic tub on floor and in minute or so it goes on to like rinse in spin. all the way to end. installed new pump.

I am Changing a DC97-18439A Clutch assembly for the Fist time. I do not see a see a relevant video on your Site.
Which on is close?

We have a Samsung fridge displaying FF

Display panel is not lighting.

What does it mean when the control panel display shows OF on freezer and refrigerator sides ?Samsung model # RS267TDRS.

What does it mean when the control panel display shows OF on freezer and refrigerator sides ?Samsung model # RS267TDRS

Samsung dual cooling fridge, initial problem is fridge compressor is running but both freezer and fridge evaporator fan motor not working , and error code is E22, which mean evaporator fan motor, motor resistance is ok but get some burning smell from control board, change control board parts number DA92-00592A, now fridge is working good but there is no cooling in freezer compartment, should i need to change all three control board including invertor board?

need help. thank you

shailesh from mr appliance saskatoon canada

My Samsung gas dryer, DV419AG, is two weeks old, I have 21 feet of 3″ dryer vent cleaned today and it is still taking a LONG time to dry 8 towels, about 2 hours. It is not getting too hot, runs heater only for 30 secs. It says in manual it should have a 4 inch vent pipe, I am in a condo and it is old vent pipe 3″, should I replace it or is there a cutoff switch that can be set for heater to stay on longer to heat up the dryer? HELP.

WHEN WASHER IS POWERED UP THE DISPLAY SAYS THE DOOR IS LOCKED AND IT CONTINUOUSLY
UNLOCKS THE LATCH BUT IT IS ALREADY UNLOCKED.

The control board is receiving power.
I thought maybe it’s a bad control board and it’s not powering the touch panel to start the unit so I replace the control board and I still have the same issue.
I’m not getting power to the touch panel to start the unit.
Door switch is also not getting any power.

I have a 2009 Samsung 28.5 cu ft refrigerator with french doors and ice and water service on the outside of the door. It is model #RFG297AARS, BOM # XXXXX with TWIN COOLING Plus. It has a SPACE Icemaker. The compressor is BK190C-L2C.
After just over four years of operation, the ice maker stopped producing ice. The water filter has not been replaced for a couple of years; however, it is not clogged. The water dispenser on the door still flows as it should. I removed the filter and the water still flows as it should.
The ice maker started slowing to the point that we were getting only a couple of blocks of ice at a time. Then it stopped producing completely.
I have tried holding the reset button for ten to twelve seconds with no results.
How should I go about doing any further test to determine the problem. I have not replaced the filter yet but plan to do so.