Brand: Samsung

need service manual for my samsung refrigerator

Hello,
The samsung fridge is not cooling or freezing. I found codes 83 and 84 related to the compressor and went ahead and replaced the inverter board. The board light stays on steday and the fan runs on the compressor. I think this indicates normal operation. However its still not cooling or freezing. I don’t know if there are steps to take to reset the fridge. i have left it unplugged for an hour with the hope that it would reset and start to cool. I have also looked again at the error log and nothing new is reported. I ran the self diagnostic 2 fridge sensor error and received a “C” in the response thinking that a temperature sensor might be the problem. These are the parts I considering to replace but want to know if I’m in the right

Temperature sensor (DA32-00029Q)
Thermal fuse assembly (DA47-00301B)

• Samsung Refrigerator mode # RF28R7351SR/AA
  ICE shute opens and closes on its own. The display works fine and you can change between water, crush or cubes. The shute opens and closes repeatedly non stop. Dont know where to begin troubleshooting.
  Thank you

I have a Family Hub Refrigerator with 4 doors. The freezer section (bottom left) no longer freezes. The flex zone (bottom right) now seems to not be cooling as well as it use to (used as a fridge). Fault history shows error 83: Compressor Current & 84: Compressor Motor from about 6 weeks ago. However, those faults do not show anymore when running a self-diagnosis. I receive no errors during a self-diagnosis. I’m. trying to figure out if I should try replacing the PCB inverter board, or if it’s a more serious issue.

The dryer is not heating. We checked the element, the fuses and everything checks ok. We checked the airflow, unhooked the duct and ran it. Checked out ok. The motor is spinning. What parts should we replace in this dryer sequentially to repair unit?

After beginning a cycle, the initial fill seems to take longer than normal. After a few moments, the unit begins to drain (without beginning to wash) and the “Smart Auto” light blinks.
I have cycled power to reset.
I have also already replaced the thermistor.
There is no water in the drip tray beneath the unit.

This washer machine does not power on any more. I would like to know what parts besides the PCB main board would help solve this problem. Please provide part numbers and diagram of the washer. Does this washer have a noise filter that can solve this problem. Any advice would be help full. They only thing tried was changing the power cord which worked for a few washes before no longer powering on. This is a Samsung washer.

Costumer explained Dryer door opens during operation. I ran the dryer and the door never opened.

Already checked and tested power, fuses, magnetron, capacitor and wiring harness for damage.

The washer turns on and goes through the washing cycle. It drains the watet after rinse. But fails to go into spin mode.

I Keep getting smart auto and heavy lights blinking after the dishwasher is running maybe five minutes, It seems like when it starts it automatically drains. I’ve reset the dishwasher multiple times each time it allows the psycho to go a little bit further but it doesn’t look like it’s putting much water in the dishwasher.

Last week I noticed the clock starting losing time. Then both timers stopped counting down when set. Now the interior lights don’t go on when the door is opened. So far, burners and oven work fine.

See above. Newer model Samsung French Door refrigerator. Display is on the right hand side on interior of refrigerator. Above “Fridge” button flashes the letter C. Above the “Freezer” button flashes 40, 24, 25, and 65. Unit appears to be maintaining temp however it will intermittently trip the breaker. We have replaced main control board already.

OK WELL THIS SAM WASHER IS NOT SPINING REPLACED THE ROTOR POSITION SENSOR AND STILL NOTHING AND WHEN DOING A DIAGNOSTIC CODE CHECK ITS GIVING ME A (AE6) & (DE) ERROR CODE THE WATER AND EVERITHING AND IT DRAINS JUST WONT SPIN I DONT HEAR A MOTOR HUMING OR ANYTHING

I am trying to replace the touchscreen control board on my refrigerator. I need to know how to remove the display panel to get to the board. Looking for help or a video to show me how to remove the touchpad to get to the control board. This is a Samsung French door four-door refrigerator not a side-by-side.

Is there any videos or do you have any instructions on how to remove the wash basin the part that’s underneath the lid as the 2020 model does not seem to have the screws on the side to detach the lid. Part that needs to be replace is DC61-04129A along with part DC97-20069A. Please advise on how this can be done. Thank you.

Machine starts and trying to fill but won’t

Washer Lid Assembly will not stay open when lifted any ideal of what parts would fix issue to hold lid up when filling washer. Looking for more detail that is better than the Spring Hinge which is hard to remove. Looking for more insight on what could be causing this problem and any detail breakdown of how to go about repair. Any videos on this type of washer with similar lid staying in place would be helpful or how to replace the lid assembly. Mainly happens when the under lid is corrected that’s when it falls down and will not stay up in place. Thanks.

Fridge has power, compressor running, condenser fan running, lights and front controls work. No cooling in fridge or freezer. Evaporator fans not running. Suction and discharge lines are not hot or cold. Fridge is new but just stopped cooling. Not sure what to do next. Any suggestions would be greatly appreciated

While trying to heat over, a low bang noise then no gas. No gas at stove top and no oven. Is this some kind of safety shut down. Or is this a problem at.the.propane tank?

My washer makes grinding noises and doesn’t spin as smooth as usual.

Spinning process is 12 mins and it will work for 10 or 11 mins and stop spinning. Instead of spinning, the machine was filing with some water.

My dryer is not heating

My Samsung dryer will not start.