Brand: Whirlpool

My Whirlpool dryer is not spinning.

DRY WILL NOT START, HAVE CHECKED ALL OF THE THERMAL FUSES, PUSH TO START SWITCH, TIMER AND DOOR SWITCH, (REPLACED THE DOOR SWITCH BECAUSE IT WAS STAYING CLOSED AT ALL TIMES), EVERY THING CHECKED OUT OK. I REPLACED THE TIMER WITH A NEW ONE JUST TO SEE IF THAT WOULD HELP, NOTHING. SO I THOUGHT NOTHING LEFT BUT THE MOTOR, NEW MOTOR STILL NO START.
THIS IS WHERE IT GETS GOOD, IF I DISCONNECT THE START SWITCH AND CHECK THE TWO LIGHT BLUE WIRE THAT THE WIRING DIAGRAM SHOW IS THE WIRES THAT ARE IN THE START CIRCUIT, I GET 120V FROM EACH WIRE.
SHOULDN’T I ONLY GET 120V FROM ONE WIRE, (POWER COMES IN ON ONE WIRE, PUSH START SWITCH AND POWER THEN GO THOUGH TOTHE OTHER WIRE. ) YET I AM GETTING 120 ON BOTH WIRE ALL THE TIME. DO I HAVE A DEAD GROUND SOMEWHERE? WHAT ELSE CAN I DO TO DIAGNOSE THE PROBLEM . THANKS

Dishwasher leaking by bottom corners of door
How do I fix this?

My Whirlpool washer is making loud noises while spinning out.

My whirlpool washer will not agitate.

My washer will not spin.

Making loud noises and displaying error codes.

My washer is shaking and seems to be off balance.

My whirlpool washer is making grinding noises and also displays error codes.

My whirlpool washer is not draining water properly.

My Whirlpool washer is leaking water from the bottom.

The lid on my washer is scratched up. I am looking for some advice on how to replace it.

My whirlpool washer is not getting any water.

I cannot open the lid of my washer.

My Whirlpool washer is not filling with water.

My washer will not power on or do anything.

My washer is giving me error codes and I do not know what they mean.

I bought a brand new in the box dishwasher that was 2 years old. I plugged it in and it didn’t clean very well. I tried all of the cycles and still not clean well. I checked the water input to the water inlet valve and it was strong. I then pulled the hose from the water inlet valve to the inlet assembly and it seemed strong. I did notice that when I run a cycle the arms never move. There does seem to be water in the dishwasher and it drains just fine. I tried adding a couple of quarts of water to the bottom of the dishwasher to see if not enough water and still the arms didn’t seem to spin. I bought your video on diagnostic modes and when I run it I received the following codes before the test happens. If it were new from the store I could ask whirlpool but since I bought it second hand, even if it was new in box, I can’t,

F4 E3
F4 E3
F6 E4
F- E-
F- E-

Replaced icemaker, still no ice. 120 volts going to the icemaker

The water valves have been changed. Water pressure is good. The icemaker fill test #25 passed and the icemaker filled but will not on its own.
I noticed that the right hand refrigerator French door pops open when they shut the left hand door. Could this cause the ice room to be too warm and not make ice?
What else can cause this issue?
What else can I check?
How do I adjust the French doors to solve the problem of the door always coming ajar?
THIS IS A WHIRLPOOL REFRIGERATOR

The spark ignitor clicks and the bake burner comes on but the spark ignitor continues to spark for about 20 seconds
then the burner and spark ignitor stops. Then it retires every 1 to 2 minutes

What is the issue here?
In the diagnostic mode it showed F6E0.
This is a communication problem.
I tested the harness between the interface and the control. It was good.
I unplugged the unit and cleared the code but the BAKE still does the same thing.
In your experience what is causing this?
The ground is hooked up.

The dishwasher stopped cleaning. I determined it was not filling with water. I found the screen on the inlet valve was plugged. I removed it and cleaned it out. It now fills with water but when it gets to what would be the wash cycle it just sits for a few minutes and then goes to the drain cycle. I have unhooked the power to reset it and still has the same problem. I also added more water to it to make sure it wasn’t a water level issue and it still will not go to the wash cycle.

I need the tech sheet so I can do diagnostics.
What is the most likely reason for this model to stop producing ice

Lihgts are constantly in pause , I tested the lid switch and it’s ok , I need to enter the diagnostic mode .

All the dryer does is flash pause. It won’t even let me cancel. Therefore I can’t retrieve errors or run the service mode. The door switch tests good.

There is an inch of ice in the floor of the ice room. Is there a service bulletin on this issues?
I suppose the customer has to let it thaw out.
Is this a problem with the water valve? The FILTER has been changed and water pressure is good. The icemaker was replaced 8 months ago.
Any information about this would be helpful.

whasher works fine on first load, goes through all the cycles and clothes come out as it should, it fails on second load to spin on high speed, it rinses fine, but it wont go through final spin (high spped), so clothes are too wet, no error codes, diagnostic shows no problems, it keeps trying to balance I guess but it wont go through with it and it times out after too many attempts, I`ve replaced the pump, think it has a faulty pump, shocks looks good as well, need help with this customer machine problem, cant keep replacing parts, any idea?

hello, this front load washer is about 6yrs old. Complaint tub bangs and sounds off balance. I started drain & spin cycle WITH NO CLOTHES IN IT and once it began to spin the tub started banging. as it picked up speed it stopped banging and sounded normal. So its when it first starts to spin bang bang then it settles down. THIS WAS WITH NO CLOTHES IN IT.