Whirlpool oven
- Guest asked 5 years ago
- last active 5 years ago
When I push the power button select cycle push start normally the you will hear the door latch lock and the sensing light will light then the washer will go thru its regular routine of going thru the wash cycle. Now when I push the power button, select the cycle, push the start button NOTHING WILL HAPPEN, NO ERROR CODES!
- Apache Warrior asked 9 years ago
- last active 9 years ago
Makes ice seldom leave and then melts and runs out onto the floor did it in error code for icemaker test drive noted in bed going to replace icemaker but I’m assuming I have a cooling issues also
- dwoods asked 8 years ago
- last active 8 years ago
- Guest asked 7 years ago
- last active 7 years ago
On diagnostic test all good . High spin as well. But during the cycle no high spin. Sometimes stuck too long on 13 min to end
- Guest asked 7 years ago
- last active 7 years ago
The dispensers are clean and not restricted. When I run the diagnostics they overflow especially on warm. I first noticed this issue when I tried to run the clean cycle and at the very beginning when the bleach dispenser fills for about 20 seconds it overflowed. I removed the dispenser to check it for a clogg but it was clear and clean. Is this a valve problem? It has a sound like the Pressure is very high but the house pressure is normal.
- Guest asked 8 years ago
- last active 8 years ago
when this happened i tapped on the right pressure switch and it would fill. i replaced switch and it still happens also when it does fill it only fills halfway. this only happens on rinse, works fine during wash cycle
- Guest asked 8 years ago
- last active 8 years ago
Do you have a service manual for this refrigerator?
Do you have any videos on how to replace the diffuser #w10814173?
Thanks.
- Guest asked 7 years ago
- last active 7 years ago
Hello
Have a problem with my Whirlpool washer Model LSR8433KQ0.
The agitator works and fresh water will come into the tube,
but when the timer moves to any “Rinse” position the dirty
water does not pump out and the spin cycle doesn’t happen.
There is a humming noise when the timer goes over the “Rinse”
position but nothing happens.
Removed the pump, motor, and checked the motor coupling.
Outside the unit the motor shaft turns easily and turns the pump shaft.
I can turn the rubber/plastic coupling still inside the machine with my hand
and it turns the agitator OK.
Your expertise for a repair solution is very much appreciated!
Regards
Bruce
- Curtis Appliance Repair asked 7 years ago
- last active 7 years ago
Does this unit have any service flashes or job pointer concerning the bake burner and spark ignitor kit .This is a DSI system? The gas ports are clean. The oven has run for years with out the Ground supplied through the outlet. The wiring is good. No bare insulation.
Is there a service manual available?
- Guest asked 7 years ago
- last active 7 years ago
I tried blowing air through the drain hose and it would not go through
I ran the machine on cold water only with the cold hooked up rapid wash cycle got an A09 error
But when I ran the the machine completes cycle with no error
Carey
- Guest asked 5 years ago
- last active 5 years ago
Customer complaint is the washer has increased spin speed in the last week or two
Spinning too fast
- Guest asked 8 years ago
- last active 8 years ago
Without disassembling the over the range microwave. When it operates but will not cook is there a way to determine if its the transformer or even capacitor and Not the magnetron and diode that need to be replaced that you guys state in your repair videos for microwave not heating???
- Guest asked 7 years ago
- last active 7 years ago
It shows an f9e2 long drain error code but pump works great and the pressure hose is OK. and the fill on a normal cycle is fine. In the spin and agitate it make a distinct slight grinding noise( not pronounced) It sounds like it could be the spin bearing. I have never seen this model. It looks like it could be a new design or a samsung.
- Guest asked 9 years ago
- last active 9 years ago
GOOD EVENING. I AM TOLD THAT THE DRYER IS TAKING TOO LONG TO DRY. SOME TIMES IT WILL WORK BETTER ON DIFFERENT CYCLES, BUT THE TEMPERATURE SEEMS ON THE LOW END. ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.
- Guest asked 8 years ago
- last active 8 years ago
Hello
I have a unit that is not cooling enough in both Fresh food and freezer sections.
the fresh food temperatur on the display shows 33f however, the termometer reads 48f. similar difference in the freezer. 0 f but reads 11 on the termometer.
- Guest asked 7 years ago
- last active 7 years ago
Customer replaced water filter, then valve. Still leaking from dispenser.
- Guest asked 7 years ago
- last active 7 years ago
THERE ARE NO LIGHTS OR DIGITAL DISPLAY IN THE REFRIGERATOR COMPARTMENT. I THOUGHT IT WAS THE DOOR SWITCH BUT THAT IS GOOD. HOWEVER, I’M ONLY GETTING 50V AT THE SWITCH AND IT FLUXUATES. I HAVE SEVERAL OTHER TEMP CONTROL ASSEMBLIES AND THEY ALL HAVE THE SAME ISSUE. THESE CAME OUT OF OTHER UNITS SO I SUPPOSE THEY COULD HAVE THE SAME ISSUE. THE ORIGINAL ASSEMBLY WOULDN’T KICK THE COMPRESSOR OR FANS ON AT ALL. I’M NOT SURE OF THE CURRENT PATH OR IF THE POWER IS ROUTED THROUGH ONE OF THE BOARDS IN THE CONTROL UNIT. ANY THOUGHTS WOULD BE APPRECIATED. THANKS
I’M GETTING THE SAME VOLTAGE TO GROUND AS THE NEUTRAL.
I CORRECTED THE MODEL NUMBER THE S WAS A 5.
- Guest asked 8 years ago
- last active 8 years ago
I have had several of these French door whirlpool brands lately that are over cooling the fresh food refrigerator side to the point of freezing. I set all possible settings to minimum or least cold. Partially covered the vent holes just to experiment. This particular model I tried to find the damper door to see if it’s closing but couldn’t find anything besides a tiny one on the side of the icemaker compartment. Please give technicians insight mostly because when I ask these questions I’m usually long ways away from the unit and onto the next job.
- Guest asked 7 years ago
- last active 7 years ago
CAN A LID SWITCH CAUSE NO LIGHTS COMING ON. GREEN LIGHT ON BACK OF CONTROL MODULE THE ONE WITH PRESSURE LINE ON IT. I REPLACED THE MODULE WITH A GOOD ONE I HAD IN STOCK AND NO DIFFERENT.
- Guest asked 6 years ago
- last active 6 years ago
Can you get me the tech sheet for this unit. I need to know how to run a diagnostics. Any and all info is welcome. Thanks in advance.
- Guest asked 6 years ago
- last active 6 years ago
so they say the dryer will go off mid cycle.
I checked the motor by letting it run and turning it back on and off and on a d it restarts no problem.
what may I be missing?
- Guest asked 9 years ago
- last active 9 years ago
First there is no diagnostic tech sheet in the unit. The damper is open and the freezer section is below zero. The refrigerator is 66. I could not test the unit with out the tech sheet. I suspect the freezer section is frosted.
- Guest asked 9 years ago
- last active 9 years ago
error f70
- Guest asked 7 years ago
- last active 7 years ago
good starting point to troubleshoot this brand new machine…120v ac each leg including feeding back through neutral.5 volts difference between right hot leg and neutral. what the??????
- Guest asked 9 years ago
- last active 9 years ago
We are having an issue with this wall oven showing an F6E0 error code when going into the diagnostic mode. After researching, we found it is an issue with the boards or control panel. Is there any way to test which is the faulty part causing this issue?
- Guest asked 7 years ago
- last active 7 years ago
replaced 4 suspension and the sensor problem not fixed
what do you think is the problem
- Guest asked 6 years ago
- last active 6 years ago
To whom it may concern,
I have a Whirlpool WRF757SDEM refrigerator that has cooling issues in the refrigerator section of the unit;not the freezer . The bottom fresh drawer is ~ 33 degrees, the 3 drawers above that are ~ 40 degrees and the upper main is ~ 47 degrees.These temperatures have been verified by placing thermometers in each section. Due to this elevated temperature we also have had to shut the iced maker off as the ice would melt in the door compartment causing water to run out the chute. I have had a large amount of ice forming behind the bottom drawer ( the one at ~ 33 degrees) and have had to remove this 3 times as it build up there and has caused issues shutting that drawer. The ice was in all the vents located there and I had to take care so it would not get damaged. The freezer portion of this unit works fine and freezes ice in ~ 30 minutes.
I am hoping there is a repair for this erratic cooling as the unit is barely 6 years old and is just out of warranty.
Any and all assistance would be greatly appreciated.
- Guest asked 4 years ago
- last active 4 years ago