All Answers

I found a video on replacing this part on a very similar washer.

Hi. I found another similar washer. Attached is a link to many videos on this washer. Take a look at the mode shifter video. This will show you how to disassemble the unit underneath to get to the part you want to replace. There are just a few bolts left to remove that hold the assembly to the tub. You will need to remove the basket as well.

Hi. I could not find any video for this specific repair. I did find a video on a similar unit that will show some of this repair. In the video they show removing the whole basket out of the unit. You will not need to remove it on your unit. I also attached the mini manual that shows how to take your unit apart.

Hello
I believe the fuse you are referring to is in the heating circuit only. I have provided the technician diagnostic manual along with a Service bulletin. See links below Matt Ace technician

Hello
See the technician diagnostics manual link below along with the #76 page Job Aid. Matt Ace technician

Hello
See the manual link below on the DPGT750 series breakdown along with the wiring diagram and video. Matt Ace technician

Hi. What happens when it stops at 17 mins? Does it do anything? Is anything running? Is it full of water, or empty? If it will not advance from 17 mins and you are not getting any error codes, it seems like you would have a faulty control board. Let it sit for 30 mins or more at 17 mins so it has time to pull an error code. Is it trying to spin and going off balance? Attached is the tech sheet. I found no pointers for this issue.

Hi. Is the ice maker not producing ice? Are cubes getting stuck in the ice maker? Or are you having a frost issue in the ice chute and on the ice bucket? IF your issue is frost, warm air is entering the unit. Most likely the ice chute door is not closing/ sealing. Take a look at the ice chute door. IF it needs replaced it is part # W10889430. I have attached the owners manual that will have your warranty info in it and the tech sheet.

HI. I can not find a video for your exact model. All the videos I find have screws to remove on the bottom trip piece. There could be tabs to release on the bottom. I have attached a video that show tabs on the bottom. This video is not for the same brand so yours would be different. If no tabs on the bottom then there are tabs around the display. You will need something small, like a putty knife to slide into the gap between the door and Display to pry it out, but be careful to not scratch or damage the door. I looked up a picture the the control and is shows two screws on the bottom to remove after the bottom trim is removed so I do not think it would have tabs to get with the putty knife. Also, try taking out the spill tray on the bottom of the dispenser. There will be a screw under it to remove. This may remove the bottom trim and then revel the screws to remove for the upper one.

Hi. Yes, there is a fan in the refrigerator. You will need to replace this fan to fix your issue. I have attached a bulletin for you and the fan. It looks like you do not need to upgrade the software any longer. Just the fan is needed. Double check that your model number is on the bulletin.

Hello
See Ice maker diagnostics are on page #87 in the link below. Also see the ice maker service bulletin link. I have also provided GFE28 series video’s .

Hi. It sounds like you have an issue with the dispenser module or the user interface control. The dispenser module is p# . I have attached a video for a similar one. The User interface is p# 242041101. Check the switches on your dispenser module. Check that the paddle is not making contact with the switches as well when no one is pressing the paddle.

Hello
I have attached the manual for the baffle module diagnostic test. See links below. Matt Ace technician

Hello
See the service manual links below. Diagnostics are on page #37. As long as the diversion valve is working properly you have a sealed system issue. The diversion valve rarely has issues, you can go through the diagnostics on the valve to be sure.

Bellow is a link for the part you are looking for.

Typically error code E31 on Electrolux models indicates that it has detected an internal generator error on left side cooking zones.

F152 means the right front burner has failed, the sensor in it is bad, the burner will need to be replaced.

Below is a link for the part you are looking for.

Unfortunately it looks like that main pcb board is no longer available.