All Answers

Hi. By griddle igniter are you referring to one of the igniters of the cooktop? If so and you have already replaced the burner switch and spark igniter then you most likely have an issue with the spark module or possibly wiring. The spark module is p # WB13T10078. I have attached the service manual and mini manual on this unit for you.

Hi. It sounds like you may have wired the damper wrong. Only one the the switches of the damper will be used with the new harness. The new harness only has one plug for the switch and you need to install it on the correct switch. I have attached a repair video on this. At 5:20 in the video it shows which switch to plug the harness on to. This should be the issue if you did not have this issue prior to installing the new ADC kit.

I have attached a tech sheet for your model number

Hello, not much information found on your exact model, however I have attached several Bosch dishwasher repair videos pertaining to a no start issue and also a Bosch dishwasher training and repair manual for you.

I believe i found what you are looking for . Chopper blade assembly part number DW-1625-01. The filter screen part number DW-2800-014.I have attached a link for each part for you .

Hi. Viking does not currently have any technical information for this unit. I could not find a tech sheet or wiring diagram. It looks like you have a control that would control those 2 burners. There are 3 of these controls and it looks like they each control 2 burners. I would suspect that this is your faulty part if the burneres went ba at the same time. It is part # 041802-000. You may be able to visually inspect this part to find a burn mark or damage.

Hello
See the links below to help with your issue. The only wiring diagram we had was for a ME21F70 series. It it very close to your model. Hope this helps , we do not have the exact model wiring diagram. Matt Ace technician

Hello
See the complete diagnostic manual link below. The ( PO) Error is a power out message.Press the ‘measured fill’ button on the front panel for 2-3 seconds. It is right below the word ‘confirm’ on the display. It makes you confirm that you know the power went out so you don’t eat any refrozen food. I would then run the unit through diagnostics. Matt Ace technician

To ENTER SERVICE DIAGNOSTICS Mode:
Press SW1 and SW2 simultaneously for 3 seconds. Release both buttons when you hear the CHIME
indicator. Unit must not be in Lockout prior to entering SERVICE DIAGNOSTIC MODE.
The display will show 01 to indicate the control is in step 1 of the diagnostics routine.

To EXIT SERVICE DIAGNOSTICS Mode: do one of the following 3 options:
• Press SW1 and SW2 simultaneously for 3 seconds.
• Disconnect the product from power.
• Allow 20 minutes to pass.
• Following the exit of the diagnostic mode, the controls will then resume normal operation

Hello
See complete diagnostics manuals below. Element testing is section 3-24 in the service manual section below. Matt Ace technician

Hello
The best place for parts on Haier is Sears. See link below. Matt Ace technician

Hello
See parts breakdown link below and service manual link. Matt Ace technician

I have attached the complete LG manual for your model.It is a 118 page complete guide with all testing and diagnostic procedures. Any information you seek will be found in this attachment.

Here is the owners guide for you as well.

I have attached the complete tech sheet including all diagnostic procedures and wiring diagram for you.

Hi. After doing a little research I found this to be a fairly common issue. It appears the issue is the centrifugal switch in the motor. You will need to replace the motor to fix the issue. p # DC31-00055J. Some other complaints I saw talked about the dryer only running for a few seconds just like yours, and then after 5 minutes or so the dryer would turn back on and run again for a few seconds. This cycle would repeat until the cycle was over. I have attached a service manual that is similar to your unit and a repair video for a motor on a Samsung dryer that should be very similar to yours.

Hi. I came up with the same thing. I took a look at the parts break down directly from frigidaire and got the same part number. Make sure your model number is correct. Make sure you get it directly off of the unit. If this part will not work for your unit it must me an error on Frigidaire’s end. You would need to contact the manufacturer or possibly your parts distributor to get the correct part number. I have seen this happen before. I some looking around and did not find any other info on this part. I could not find any videos either.

I have attached the service manual for your unit. I am not finding a fill tube heater for this unit. I did not find one on the parts break down. The fill tube freezing could be a result of low water pressure also. The valve could not be closing all the way allowing a small amount of water to flow through and freeze.

This is most likely an issue with your drive assembly (transmission) . I have attached a video for you. This is of a Maytag washer, however it is the exact same as your model

Hello
See the service manual wiring diagram link below. This is A very basic model, power comes into the timer . I would check power in and out of the timer. Matt Ace technician

Hello
The freezer fan circulates air into the fresh food section. There are other possibilities if the fresh food is not cooling properly. See the diagnostic link below. Go to page #42 for ( poor cooling in fresh food section ) for more detailed diagnostics. Matt Ace technician