Filter
Sort by: Newest First
0 votes
In reply to: Bottom freezer door off track

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Lights are out

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: not level

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Washer not starting, does not go into diagnostics

See answer above question….

0 votes
In reply to: Washer not starting, does not go into diagnostics

Hello

              See the diagnostics below. Are you getting any error codes ?  Are you sure all connections to the board are good with no corrision ?  Have you unplugged the unit for two minutes to see if the board cleas and resets ? You could also have a harness to main PCB issue causing unit not to go into daignostics. If you go throgh these steps above I would replace the harness and the board at the same time. See complete manual link below. Matt Ace technician

( Test )
1. Place the Cycle Selector knob in position 0 (12 o’clock).
2. Place the Temperature Selector in the High position.
3. Place the Dryness Level Selector (for select models only) in High/Extra-Dry.
4. Perform a Full Control Reset by pressing and holding the Cycle Selector knob for 6 seconds OR unplug the power cord,
wait 5-8 seconds, then reconnect the power cord OR Cold-Power On.
5. Within 15 seconds of the reset (or power up), with the Dryness Level Selector (if mounted) at the High position, turn the
cycle selector to the Casual cycle, turn the temperature selector to the left-most (highest temp available) position, and then
press and release the Cycle Selector knob. There will be a short beep then turn the temperature knob to the right-most
position (lowest temp available) and press and release the Cycle Selector knob. There will be another short beep then turn
the temperature selector to the left-most (highest temp available) position, and then press and release the Cycle Selector
knob. This will give a two second beep to signal the unit is now in Line Test Mode.

0 votes
In reply to: Freezing everything

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Lights are out

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Smells like refrigerant

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Not keeping food cold enough

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Constantly running

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Not keeping food cold enough

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: layer of frost covering inside

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Fan making a grinding noise

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Not making ice

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: not level

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Keeps beeping

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: not keeping the proper temperature

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Leaking water

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: No cool

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

0 votes
In reply to: Spark module keeps dying

Hello
See the service bulleins links below. The ( Bulletin ) Open burner ignition wire harnesses update may be your issue. You must be logged in to see the bulletin and manual links. Matt Ace technician

Showing 4481 - 4500 of 10k results
«1...223224225226227...494»