All Answers

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

Hello
Here are a few items to check below. Also make sure you are getting +3 degrees in the freezer or below. The thermostat closes at +3 degrees and will NOT harvest unless it is +2 degrees or colder. I have provided a complete diagnostic link below to troubleshoot the ice maker in detail. Go to page 6-2 in the technician link below for complete diagnostic instructions. Matt Ace technician

The “ICE MAKER” key on the control panel activates the icemaker system. If the ice cube icon is not displayed
on the LCD, the icemaker system is OFF.
* To allow ice to freeze fully and reduce effects of low water pressure, the electronic control disables the icemaker
system for 45 minutes after each ice harvest.
* Power to the freezer lights, is monitored to help control icemaker operation. If the freezer door is open,
power to the icemaker is interrupted.
* The icemaker system is disabled when the unit is in Sabbath Mode.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

Hello
Go to page 2-2 for door adjustment instructions for your modle in the link below. Matt Ace technician

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

Hello
I show that part #WH49X10041 available at Sears see link . Matt Ace technician https://www.searspartsdirect.com/partsdirect/showCart.pd

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

Hello
There are no service bulletins on this issue. I have provided a technician service sheet link below . Are you sure the ice maker is filling to the proper water level ? See the instructions below to test the fill time. If you are getting low water pressure the ice maker will jam. And you are sure the freezer is getting below 14 degrees as the ice maker thermostat #627985 closes at +15 degrees. The Ice maker will not harvest unless its +14 degrees or lower. An easy way to check is ice cream, if ice cream is solid it is at least +10 degrees. Matt Ace technicioan

To ENTER SERVICE DIAGNOSTICS Mode:
Press SW1 and SW2 simultaneously for 3 seconds. Release both buttons when you hear the CHIME indicator.
Unit must not be in Lockout prior to entering SERVICE DIAGNOSTIC MODE.
The display will show 01 to indicate the control is in step 1 of the diagnostics routine.

To EXIT SERVICE DIAGNOSTICS Mode: do one of the following 3 options:
• Press SW1 and SW2 simultaneously for 3 seconds.
• Disconnect the product from power.
• Allow 20 minutes to pass.
Following the exit of the diagnostic mode, the controls will then resume normal operation.

Service Test – 25 Water dispensing and icemaker fill test
• Confirm Icemaker valve in fill test. The the icemaker will show icemaker fill status. Press the water pad to
initiate the water dispense.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.

Hello
It definately sounds like the main PCB. I have provided a technician diagnostic sheet. I would run the unit through diagnostics before replaceing the control. See links below for manuals and videoes. Matt Ace technician

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.