All Answers

You provided an incomplete/invalid model number, however the GSD series is quite old. You will want to see if the motor-pump mechanism is running.If so then you most likely have a drain obstruction.You also may have a bad drain solenoid. Be sure that a new disposal wasn’t just installed without the knock out plug removed. I have attached a couple of videos of a Hotpoint dishwasher which was made by GE and has the same drain system and motor-pump as you have in your GSD model and of a GE dishwasher drain solenoid replacement which will also be the same as the GSD model.

Hi. you are on the right track. If the heater and defrost t-stat are good, then your sensor or control board are faulty. It is more common for the defrost sensor on the evaporator to be faulty. I have attached 2 service manuals that are similar to your unit. There, you will find how to test your sensor. If you find the sensor to be with in range and end up replacing the control board, I would still recommend replacing the sensor as well.

Hello
The ice maker could be leaking Part #: DA97-12317A . As long as the compartment is sealed replaced the ice maker. See service manual link below.

Hello
The F6 E8 error is a Lost communications with Microwave Oven Appliance Manager. There is not a servive bulletin currently for this error. There is only only one service for this product and it is a E1 FO erroer not related to your issue. The diagnostic procedure is on page #7 for your F6 E8 error. I would take this step by step and pin out the board as directed in the technician sheet below. It sounds like it may be a UI board if you have replaced the appliance manager. But allways go through the diagnostic procedure to be sure it is a correct diagnosis. Matt Ace technician

Before proceeding, verify the error code by pressing CANCEL>CANCEL>START to enter the Diagnostics Mode, then pressing the numeric “3” or “6” keys until the error code screen is shown.

Hello
See the complete technician link below . Matt Ace technician

The F3E2 error is a few possibilities :
1) Oven sensor opened
2) Oven sensor shorted
3) BAKE/BROIL range over temperature CLEAN range over temperature.

Diagnostic procedure
1) Press CANCEL>CANCEL>START to enter the Diagnostics Mode. Verify the sensor
temperature reading is at room temperature (typically 50 to 90°F [10 to 32.2°C]) and verify
failure code. If failure code does match, then continue.
2. Unplug range or disconnect power.
3. Check all sensor connections on harness and board.
4. Disconnect sensor from harness.
5. Measure sensor resistance between connector pins and confirm reading is between
1000Ω and 1200Ω at room temperature. Also measure from sensor connector to sensor
casing for possible short. If measurement is not correct, or if short is found, replace
sensor.
6. Trace wires and connectors to sensor from control, then back to control. If wire or
connection is damaged, replace the harness. If wire or connector is not damaged,
replace oven temperature sensor.
7. Reconnect the sensor to the harness.
8. Replace all parts and panels before operating.
9. Plug in range or reconnect power.
10. Press CANCEL>CANCEL>START to enter the Diagnostics Mode and clear the error
code.
11. Press CANCEL to cancel the Diagnostics Mode.
12. Press BAKE and START. Observe for longer than 1 minute.
13. If failure does not reappear, stop. If failure remains, unplug range or disconnect power and check wire connections.

Hello
See technician diagnostic sheet link below. I would start by runiin g the unit throgh diagnostics.

Matt Ace technician

SERVICE DIAGNOSTIC MODE
These tests allow service personnel to test
and verify all inputs to the machine control
electronics. You may want to do a quick and
overall checkup of the washer with these tests
before going to specific troubleshooting tests.
ACTIVATING SERVICE DIAGNOSTIC MODE
1. Be sure the washer is in standby mode
(plugged in with all indicators off).
2. After initial power is applied, wait
30 seconds before activating Service
Diagnostic mode.
3. Select any three (3) buttons (except
POWER) and follow the steps below, using
the same buttons. Remember the buttons
and the order that the buttons were pressed.
Within 8 seconds,
• Press and Release the 1st selected button,
• Press and Release the 2nd selected button,
• Press and Release the 3rd selected button;
• Repeat this 3 button sequence 2 more times.
4. If the Service Diagnostic mode has been
entered successfully, all indicators on the
console are illuminated for 5 seconds with
“888” or “88” showing in the Estimated Time
Remaining (Whirlpool) or Estimated Cycle
Time (Maytag) seven-segment display. If
there are no saved fault codes, all indicators
on the console will momentarily turn off,
and then only the seven-segment display
will come back on and display “888” or “88”.
NOTE: The Service Diagnostic mode will time
out after 10 minutes of user inactivity, or shut
down if AC power is removed.

Hello
See complete diagnostics in the links below. ATry to enter unit into the diagnostic mode. If you cannot get the unit into the diagnostic mode unlug it it for 5- minutes to reset the board.

DIAGNOSTIC TEST MODE
1) Be sure the washer is in standby mode (plugged inwith all indicators off; or with only the ClothesClean or Done indicator on).

2.Select any one button (except POWER, START,STOP and PAUSE/CANCEL) and follow the stepsbelow, using the same button (remember thebutton):
a.Press/hold 3 seconds.
b.Release for 3 seconds.
c.Press/hold 3 seconds.
d.Release for 3 seconds.
e.Press/hold 3 seconds.➔If this test mode has been entered successfully,all indicators on the console are illuminated for5 seconds with88showing in the EstimatedTime Remaining two-digit display.➔If indicators do not display as described above,the press/hold/release procedure above may nothave been performed within the time framenecessary for successful entry. Repeat step 2 toensure this was not the cause. If stillunsuccessful, see Diagnostic: UnsuccessfulEntry, page 1.3.The program then checks for saved fault codes:➔If there are saved fault codes, see Diagnostic:Saved Fault Codes.

Hello
See link below and go to page 2-22 in the training service manual link. You must be logged in to see the manual. Matt Ace technician

Hello
See the links below and follow the Troubleshooting chart on complete diagnostics for your exact model. Also see parts breakdown link. Matt Ace technician

Hello
See the (Job Aid) link below page 4-4 for evaporator replacement details. We do not have a video on the exact model you have. I sent you an evaporator video on a french door model. Matt Ace technician

Hi. I’m not sure what would cause warm air to enter through the ice maker vent and cause burn marks. That is very strange. The air from the freezer comes through theses vents to the ice maker. I would assume you have a temperature issue as well. What is the freezer temp? Maybe the air is being circulated during the defrost cycle. This should not get hot enough to cause burn marks though. All that being said, if you installed a new ice maker and it is getting proper water, there must be a temperature or air flow issue. It is strange it starts working every 3 weeks? Does the unit get turned off for a period of time or anything else that can affect the unit? i have attached a service manual from a similar unit for you.

It is very possible the motor is bad. Check to make sure you have proper power to the motor. There is a fuse between the motor/inverter and main control that could be bad as well. P# WH49X10055. It is part of the white/ red wire. You can unplug this wire at the main control and from the motor and check for continuity. If this fuse is bad something may have caused to to fail. I have attached a repair video for the fuse.

I ATTACHED FILE AGAIN FOR YOU IN A WAY YOU SHOULD BE ABLE TO VIEW . IT IS THE COMPLETE SERVICE MANUAL FOR YOUR MODEL

Hi. I have attached a new link to for the service manual on this unit. I am not sure on this model if the basket should spin freely. Depends on if there is a brake that could be engaged or not. Typically the baskets on these style washers are suppose to spin freely, but I am not sure on your exact model.

I have attached the complete service manual for your model. All information you need is in the attachment. Also, I would take a good look at lid switch assembly as this is most likely cause of the issue.

I have downloaded a Dacor range service & diagnostics manual for you

Water filters are charcoal activated and when changed either 2 gallons of water must be flushed through dispenser, or you may get grey and/or cloudy ice cubes. I would be sure it is flushed properly, then inspect ice maker for build up of residue in cube mold and also look carefully at water reservoir for residue build up.

Hello
See service diagnostics link below. See some possibilitys below that could cause your issue. Go to page #19 in diagnostics to address your specific issue. Matt Ace technician

1) Check water supply – filter may be restricted.
2) Check inlet water valve – inletscreen may be restricted.
2) Spray jets partially clogged.
4) Check for a water leak at the reservoir.
5) Water leaking into bin from torn ormis-positioned curtain. Checkcurtain position and condition.Reposition or replace as needed.

See links below for the technician mode and complete troubleshooting service manual. You must be logged in to get to the manual links.