All Answers

Hi. Here is the tech sheet on this unit for you.

Hello
See the link below. Go to page #6 and #7 in the link below. This will give you excat directions on how to adjust the doors. Matt Ace technician

Hello
Some items to check with your E3 Error. First run the unit through the diagnostic mode with the technician diagnostics link below. This error occurs when the washer motor has an issue. Check the rotor/ stater first before replacing the motor. The last possibility is board. See diagnostics for each component before replacing. Matt Ace technician

• Check the motor connector terminal

connections.

• Check if the Motor Cover State is damaged.

• Check if the coil is broken due to moisture

from any alien substance.

• If the PBA control circuit is defective, replace

the PBA.

► Check the motor Winding Coil

• Plug out the connector and read

resistances at any two of the three

terminals on Motor

Should be 19.3Ω (at 25oC)
Check if the washing Motor
Rotor/State is defective or
not.
This may occur when the
main PCB is

The PBA connector terminal is not connected.
– The motor spin net is not engaged.
– The motor’s internal coil is damaged. (short-circuited or cut)
– The hall sensor terminal is not connected.
– Foreign material (a screw) has entered the motor.
– Motor overloaded due to too much laundry. (Non-sensing)
– The motor hall sensor terminal is not connected.
– PBA fault.
– The motor driving error from the PBA is weak.
Unstable relay operation, etc.
– This occurs due to erroneous operating signals from the motor
hall sensor.
– The IPM terminal of the main PBA is not connected.
– The DD motor cover is out of place.
– The PCB housing terminal is not connected.
– PBA fault.
– DD motor fault

Hello
Are you getting normal freezer and refrigerator temperatures. You should have -5 to +5 degrees in freezer section and 38-42 degrees in refrigerator. If you do then I would look at the door gaskets and make sure the doors are getting closed properly. If a door is ajar overnight it will cause this issue. Thanks Matt Ace technician

Hello
On this model we take a socket set with a stub 1/4 inch drive and remove the three screws on the back of the condenser motor. Its all done by feel you cant see the screws. Should take about 20 minutes.

Hello
This is a Kenmore unit not a Frigidaire. I changed the make for you. We only have a technician sheet on this model . No video as of yet. Matt Ace technician

Hello
The model number listed is not correct, please check it. The symptom sounds like a pressure switch or plugged pressure tube hose. See video links below

Hello
This sounds like a possible motor or motor relay issue. See diagnostic sheet below and video links. Matt Ace technician

Hello
We have found the water reservoir will get deposits in it from sitting. I would replace the filter and reservoir at the same time and that should correct your issue. We have run into this at least three times. Part number #DA97-07129A . Matt Ace technician

Hello
Your best sealed system class in the country is Freds in Cleveland Ohio. I dont know of any classes in Nevada . Here is link https://academy.fredsappliance.com/?gclid=CNvOyKuDi9MCFZOKswodHCgPMQ

Hi. I have attached the tech sheet, as well as diagnostic and repair videos for you. The unit could be displaying an error code. This can cause the lights to stay on. Try to reset the machine by unplugging it. Then press and hold the start button in for 5 seconds with the unit unplugged. Plug the unit back in and give it a few seconds to come back on. If the lights come back on try to press the start button for about 5 seconds until the lights shut off. Enter into the diagnostic mode to see what error codes you have stored and run an automatic test mode.

Hello
See technician sheet on your issue. If you have no display you will have no choice but install the main control board. Just make sure you have no other shorts. Matt Ace technician

Hello
It sounds like a main control board since you have no display at all. Make sure you have no other shorts before installing a new board. See diagnostics guide below along with videos for your model. Matt Ace technician

Hello
See complete service manual for your series Viking dishwasher link below. You can run through diagnostics to pinpoint your issue. Matt Ace technician

Hello
If the other dishes are dry I would try a dishwasher rinse aid agent. Like Finish Jet dry. Some dishwashers from Whirlpool Corporation—including many Maytag, KitchenAid, Kenmore, and Whirlpool models—still offer an exposed drying element. These tend to be cheaper models with plastic tubs, but some stainless-tub models also have a heated dry. If you see a black ring around the filter at the base of the machine, it’s a sure sign that your dishwasher has an exposed heating element. Hope this helps Matt Ace technician

Hello
See technician guide and complete diagnostic links along with videos. Matt Ace technician

Hello
See technician guide below. If you are getting 17 degrees in the freezer and your temperature control is set on the highest setting , you clearly have a cooling issue. You should be getting -5 degrees to +5 degrees in the freezer. 38- 42 degrees in fresh food section. I would remove the cover of the evaporator and inspect the evaporator for an even frost pattern. I suspect you have : 1) The beginning of a defrost issue. 2) A starved evaporator with a sealed system leak. Both very common issues for your model refrigerator. The condensation forming in that drawer on the glass shelf is caused by a cooling issue. Matt Ace technician

Hello
See the technician guide below. Have you replaced the water saddle vale ? It sounds like you have a valve that is leaking through. With low water pressure trickling though it will freeze up the inlet tube. You need to have good cwater pressure through the water inlet tube. Matt Ace technician

Hi. I have attached the tech sheet for you. To enter into diagnostic mode you will need to turn the knob L-R-R-R-L-R. You were missing the last R of the sequence. There you can check for stored error codes as well as run the unit through a test cycle. They did change these units to only lock the lid once it gets to spin. So it is normal that it was not locked. I have attached a video as well to show you how to gain access into diagnostic mode.