All Answers

Thanks for asking a question. I looked up that model number and we have a video on a similar issue. I put a link below the answer.

We have an video that could help you. Check out the link below.

Good question – I have gone ahead and linked a video below that may assist you

Thank you for your question, watch the video linked blow, it should help

Good question – I have gone ahead and linked a video below that may assist you

Good question – I have gone ahead and linked a video below that may assist you

We have an video that could help you. Check out the link below.

Control board Troubleshooting
Programming Mode:
Important : The Program Code is located on the Serial Plate on this unit after the word Code.
If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a
Program CODE of 0000). Once the Program CODE has been saved the Programming Mode is exited by pressing any key or by opening or
closing the refrigerator door. If the new code is incorrect this process should be repeated.
The Programming mode can be exited at any time by pressing WATER key for 3 seconds or will exit if unattended for four minutes.
1. Press and hold the WATER Keypad.
2. Press and hold LL Keypad.
3. Release the WATER Keypad and wait 3 seconds.
4. The control will display PE to indicate the programming mode.
5. Entry is confirmed by pressing the LL Keypad once more.
6. The control will display the current Program CODE. This value should be validated with the Program CODE printed on the unit serial plate.
NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing water Keypad for 3 seconds.
7. Press the UR Keypad or LR Keypad to change the digit value with each key press.
8. The decimal point indicates the selected digit. Press the UL Keypad to select the next digit.
9. Once the desired Program CODE is entered, press and hold the LL Keypad until the Program CODE begins flashing indicating it has been saved. See video link for ( KFSI) Series control board . Matt Ace Technician

Hello
I have provided the technician diagnostic sheet, go throgh the diagnostics and it will pinpoint your issue. Matt Ace technician

1. Unplug dishwasher or disconnect power.
2. Access wash impeller and verify rotation:
   ■ Rotation should require only moderate force.
   ■ If rotation is difficult or not possible, replace
   pump and motor assembly
3. Check resistance of all connections in power
   up circuit to control. Check connections
   between keypad(s) and control

Hello
The F2 is your fault code and the E6 is error code is (CANCEL key drive line open)
Fixes for this issue :
1. Check keypad connector for firm connection.
2. Press CANCEL. If error code returns after 60 sec., replace keypad.
3. Replace mail control board .

I suggest to run the unit through the diagnostic mode with the link provided below. Matt Ace technician

Hello
Does the unit function correctly with the ice maker off ? If so run the unit through diagnostics with the technician diagnostic link below. If everything is running normal with the ice maker off and diagnostics come back with no errors I would replace the ice maker. There is only one service bulletin related to this issue, but not with the ice maker .( If protective film on doors is removed after refrigerator is plugged in, the unit can go into Safe mode.
Unit will appear dead. ) Matt Ace technician

Thank you for your question, watch the video linked blow, it should help

Thanks for asking a question. I looked up that model number and we have a video on a similar issue. I put a link below the answer.

We have an video that could help you. Check out the link below.

We have an video that could help you. Check out the link below.

I looked up your model number and found a video that should help you out

Thanks for asking a question. I looked up that model number and we have a video on a similar issue. I put a link below the answer.

Good question – I have gone ahead and linked a video below that may assist you

Thank you for your question, watch the video linked blow, it should help

Based on your question I have located a video linked below that could help you,