All Answers

Jin, yes you need to shut off the saddle valve before unhooking the water line. I have provided a video to show you the vale and how to shut it off. Matt Ace technician

Jack, I have provided a video link below . I cannot pull up your model number it seems to have letters missing . My best guess is you have a spin bearing going bad. This is a major job in most cases and needs special tools. If i can get the correct model number, I could give you more specific answers. Matt Ace technician

Kou, It sounds like you may have a dead short in the motor. This is a direct short and will blow the circuit every time. You can remove the motor and have it tested at a parts store. Matt Ace technician

Otoniel, they constantly are changing the board version. If you looked it by the model number it should be the correct board. I would call your parts distributor and verify by the model number you have the correct board. They sometimes make mistakes. We have made a few videos on the Elextrolux ice makers. See links below they are very informative videos from our master technician that has allot of experience on Elextrolux products.

If you need any parts call our parts department at 1-800-830-5465 or order on line at http://www.savemoreonparts.com James, Please see video link below. This video is for the new kit that just came out from Whirlpool. It fits all dishwasher models from 2010 to current. This will correct your issues. Here are the models below it fits. Free Video on rack kit here is link. https://www.appliancevideo.com/dishwasher-rack-kit/
COMMON BRANDS
Whirlpool, Kenmore, Roper, KitchenAid
KDFE454CSS0
KUDE40FXBL4
KUDS30CXSS6
KUDS30FXWH9
KUDS30SXBL2
KDFE454CSS1
KUDE40FXBL5
KUDS30CXBL7
KUDS30FXWH1
KUDS30IXWH7
KUDS35FXWH3
KUDE20IXWH9
KUDS30CXSS0
KUDS30FXWH2
KUDS30IXWH8
KUDS35FXWH4
KUDE40FXBL0
KUDS30CXSS1
KUDS30FXWH3
KUDS30IXWH9
KUDS35FXWH5
KUDE40FXBL1
KUDS30CXSS2
KUDS30FXWH4
KUDS30IXWHA
KUDS35FXWH8
KUDE40FXBL2
KUDS30CXSS3
KUDS30FXWH5
KUDS30SXBL0
KUDS35FXWH9
KUDE40FXBL3
KUDS30CXSS4
KUDS30FXWH8
KUDS30SXBL1
KUDS35FXWHA
2010, 2011, 2012, 2013, 2014
KitchenAid Tall Tub Dishwashers
UPPER RACK DISENGAGES FROM RAILS
W10712394 (V-rail) and W10712395
(C-rail), only if listed on model number chart and within date range
Under certain conditions, the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes.
Wheel axle breaks and causes upper rack to fall when pulled out.
Correction:
Replace plastic adjusters with the appropriate stainless steel adjuster service kit:
P/N W10712394 V-rail (grey wheels), or P/N W10712395 C-rail (white wheels).
This kit includes both left and right side adjusters and all components needed to
service the upper rack.
Busted rack
Rack that comes off track
updated rack kit
new rack adjuster kit dishwasher
upper rack problem
upper rack issue
fits model years 2010,2011,2012,2013,2014
W10712394 (V-rail) and W10712395
(C-rail), only if listed on model number chart
Under certain conditions, the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out.
Replace plastic adjusters with the appropriate stainless steel adjuster service kit:
P/N W10712394 V-rail (grey wheels), or P/N W10712395 C-rail (white wheels).
This kit includes both left and right side adjusters and all components needed to
service the upper rack.

Sounds like a bad relay on the control board or possibly a door switch causing this. Kinda a strange symptom.

I have seen this issue before. As long as you do not find anything preventing the I would replace the ice fan motor. I have attached a link to the part.

If you need any parts call our parts department at 1-800-830-5465 or order on line at http://www.savemoreonparts.com See Samsung video link .. https://www.youtube.com/watch?v=Gsvye6sfO88
HI. I have attached a service guide for your dishwasher. TO gain access to components such as your control board you need to take the screws out around the door frame to separate the door. To gain access to the heater and other components you will need to pull the unit and gain access to the bottom. This is a vague error code for high temperature heating . First thing I would check is that you are getting the proper water pressure to the unit and that the incoming water temp. is not too hot.

David, if this is out of warranty its not cost effective to do. If its in warranty see parts breakdown below. You will need to replace #11 & #8 . It takes one technician between 3-4 hours to complete this job. Matt Ace technician

Jeff, at this point you have two options. 1) Rebuild the disposer with a kit. 2) Replace the disposer ..Our parts department can give you options both ways. Just call 1-800-830-5465 and have the model number off your disposer. Matt Ace technician

sound like a plugged drain i would also ck the door seals to make sure they are sealing.take freezer evap cover off and pour hot water in the drain to clear it i use a turkey baster to do this

that’s a tough one to diagnose with out being there i wound unplug components till you find the one that’s the cause sound like a dead short some where a volt ohm meter will be necessary to ck the wiring

that model doesn’t have a fan and the control is not available anymore part # 9757271 and that is the problem most likely

Did you check for the tech sheet in the control panel? There is a procedure to test the motor and motor control. I don’t have access to the document.
I would first suspect the motor control board as your problem and run the motor test.

I believe you pull the white plug off the motor control board, set the timer to delay, push start button and motor should turn. 120 VAC across black and white wires to motor control board from timer.

If you need any parts call our parts department at 1-800-830-5465 or order on line at http://www.savemoreonparts.com See video link to repair videos..https://www.appliancevideo.com/appliances/lg-lfc28768st-refrigerator/
Yes, pull the freezer grill off. There may be ice forming in the ice room fan area preventing the motor from turning.
ER IF error means the computer does not register the fan motor for the ice maker turning.
Check the evaporator, make sure it is defrosting completely. You may need to replace the defrost sensor in the evaporator area.
Check gaskets around ice maker door inside left ref door and the gaskets on the side of the left ref door. The ice room fan always turns off when either ref door is opened. Here are 15 video links to help with this repair. https://www.appliancevideo.com/appliances/lg-lfc28768st-refrigerator/ If you need any parts call our parts department at 1-800-830-5465 or order on line at savemoreonparts.com

when a compressor starts getting hard to start one of the first things to fail is the starting devices, relay and overload.
By adding a 3-in-1, you are adding a start capacitor to the starting package so it gives the compressor a boost when it starts. The addition of a start capacitor will shorten the life of the compressor so this would be considered a Band-Aid fix. This happens to be contrary to what some will say but this is the exact reason that manufacturers do not want anyone using 3-in-1s on their compressors.

I personally would not offer any type of a guarantee on one of these repairs. I have used 3-in-1s to get hard starting compressors going to save the customer’s food just to get them over the hump and have had them fail within a few minutes and then have others that have ran for years. You never know how much time the compressor is going to last.

Be sure to explain to the customer that the compressor could fail at any point and they need to start planning on a replacement and they may need to replace it at any time in the future.

Charles, I have provided a model that is close to your unit. See link below Matt Ace technician