Brand: Frigidaire

My Frigidaire refrigerator is not cooling.

Thought it just wasn’t heating up, but it actually wasn’t running at all. Looks like a busted door switch. Do you guys carry it?

My Frigidaire refrigerator is not dispensing ice.

THE CUSTOMER IS TELLING ME THAT THERE IS HEAT, BUT THE DRYING IS TAKING TOO LONG. I DID NOT GO TO SEE IT YET, COULD SOMEONE WALK ME THROUGH THE DIAGNOSIS? THANK, TODD FROM NY.

My Frigidaire refrigerator is leaking water on to floor.

My Frigidaire washer is not draining.

My Frigidaire washer will not start.

Have a customer with a Frigidaire SxS .
Lights are on but its not cooling/running.
Order power board ( 5304498781 ) and install same, mounts under freezer side.
New board completely dead, no lights or anything else.
reinstall old, lights come on ok.

Picked up 2nd new board, install and same thing completely dead.
No instruction with board, but none were needed on previous jobs, pretty easy repair.

Reinstall original part, box started working.
Customer called this AM and said lights on but not cooling.

Any one had problems with this power board. Thanks in advance

Has blinking code e68

Cannot find info on box bag is empty. Comp. was not running when I arrived at house. I unplugged box and plugged it back in. Comp and cond. fan came on and box started to cool. Lady called 4 hours latter . She said it was making ice but the #4 is still flashing and she said the ff is only down to 48. Any idea what the flashing 4 means.

my Frigidaire stove is displaying an F1 error code, keeps beeping and will not shut off.

I went to service a Frigidaire Infinity washer today, I cannot get the unit to go
Into the Diagnostic mode, Only two lights on the Console will light up. I replace the Control
Module and still get the same results, need some Help or direction..

Temps inside were not cold enough to make ice. Ran test & all components & frost pattern good. Leveled unit. Ice maker manually cycled. Let the customer know to monitor. If fails again and temps are cold enough, will need to replace ice maker. Do you guys carry it just in case I get called back soon on this?

Found the damper assembly bad but am having a hard time with the lookup on the model, someone free to take a peek and shoot me over the information? Thank you!

Hoe to remove control panal

Looks like I’ll need information on the electronic control for this, will confirm for sure when I get there but want to be able to have a handle on the parts needed before I walk through the door.

Ran into an issue today where the turn valve at the water heater was severely corroded and there’s a copper connection coming up behind the refrigerator. I removed ice from the fill tube and there is water to the icemaker, but I think it’s insufficient. We don’t do plumbing work, so what should I recommend she say when she calls someone else out to take care of this and get it properly hooked up for her?

Would this be the bearing? It’s not tumbling and the belt and idler all check out fine.

This dryer keeps getting complaints of noisy and loud conditions. I’ve checked what I can think of and just got called to go back out on it to take another look (third time). Already have replaced glides, checked idler, pulley, supports, it’s balanced, etc. I’ve got to be missing something here. One of my other guys suggested the blower wheel, would that make a lot of noise?

I HAVE NO POWER TO THE WATER CONTROLS ON THE DOOR AND THE EVAPERATOR FAN IS NOT WORKING. REFRIGERATOR BEEPS EVERY FEW MINUTES

I replaced a broken door latch & striker and am still getting a drain issue on this. Pump is fine, checked drain hose, and control checks out. What am I missing?

Serial: 4A43011509

Ice clumps in ice bucket every 3 days.

Brand New SxS Frigidaire fridge. No leaks from ice maker. Zero degrees in Freezer with good evaporator fan airflow. Ice dispenser Door and Freezer door close nicely. I thought maybe the icemaker heater was sticking on so I replaced ice maker with now improvement. Within a couple days they call back and all the ice cubes are frozen together. Any Ideas would be greatly appreciated.

I haven’t had a chance to physically diagnose this but want to take something with me since the customers requested the work be done asap for the holiday. I think it’s the console assembly but wanted to verify with you guys.

Timer on dishwasher stops when the dial pointer is at 180 degrees.
Manually move it past that point and the cycle will continue until finished. I installed a new timer but the DW is acting the same way.
Any suggestions on what I should do nest will be appreciated. Thank you.

I’ve cleared and unjammed this ice maker multiple times but it keeps happening. Should I just replace it? Can’t find any issues with water hose, valves, door assembly, etc.

I am pretty sure this is the temperature control but I can’t find the part. Did a physical diagnosis and check on everything else and it seems to be the only issue.