Brand: Frigidaire

I need a service manual, I have a parts breakdown, in self diagnostics, I’m getting error code iFO, was told by Tech. line(with customers assistance) that meant overfill, needed pressure sensor, ordered part, went back to diagnostics, first code iFO, second code i60, third i00,. What are second and third codes? I don’t have access to tech. line anymore.

the compressor will kick on and then go out rite away .
then a few minutes later it will do the same

We have a dishwasher that, what ever the remaining time, adds additional time. If there is 40 minutes left it’ll then add more time and show it has 90 minutes left. This happens with every cycle. Main control board has been replaced and the same issue continues. Any suggestions?

Dryer wont start because, even though the door is closed, it reads it as open. The Main Contro Board was replaced and the same thing still happens, any suggestions as to what could be causing this issue?

evaporator motor was replaced the adc electronic board was replaced and the damper assembly was replaced and frigde is still not getting cold it’s cool, not cold enough
please help

I need a servive manual that tells me how to disassemble and clean out wash arms and sump area of this dishwasher, I have a parts breakdown from my supplier but that doesn’t explain how to disassemble, i have cleared a lot of the jets using a bent hook tool, washer worked better for a week ???? any suguestions??
Thank you Joeclening uot jets

Recently, we experienced some frost buildup on the door of the freezer as the door did not close completely. Soon after that incident, our icemaker has not worked correctly.
It is not producing ice.

never worked on this model. 3 months old, cust complaint dishes still dirty, started unit thru wash cycle, jets on top and bottom wash arms are obviously clogged, tried taking them apart to clean with no luck, need service manual or advice on how to disassemble and repair this unit, model # lgid2475qf3a. also noted that top spray arm does not rotate even though water is shooting from arm, Its odd to me that jets are soooo clogged up for such a new machine. I have no information on this model because it is too new.

The ice maker is producing ice, but the ice won’t dispense. when actuator is pressed flap opens but auger doesn’t turn.what steps can I take to determine the problem?

so the fridge seems to be working fine.
however the freezer is not freezing.
i took off the back panel to check the evaporator coils and there is only a bit of frost on the top part of the coils.
how may i correct this issue?
thanks

i need a service manual for this beast. I need to know how to adjust the freezer door

I was getting an error message sy… and I was told to change the switch board under the front of the unit.
I changed it once it didn’t power up so I thought it was faulty.
so I changed it out for a new one.. I hot the new one and I have the same issue. it just will not power up

I’ve open the bottom of the unit figuring it may be the belt the belt is intact when he goes into the spin cycle the pump for the drain does spin only the motor is extremely hot and none of the other belts turn I try to manually turn it to the right it will not go when I try to push the ball to the left it will go in the tub itself I can turn it either way it works smoothly

I looked at this flex tray ice maker in this fridge today. The unit is not making ice and the ice melted in the bin. Temperature was 23 degrees in the ice bin area when I checked with temp gun. I have not worked on one of these before. Ice bin is in the upper left hand corner of the fridge. Temps in the fridge and freezer are perfect. I looked on . Can anyone shed some light on how to diagnose this ice maker and or send me a tech sheet. Is there another source for Frigidaire tech manuals? Thank you for any advise.

the client was complaining about the fridge being way to cold.
i changed the damper.
and a few hours later he called to say that everything in the freezer is melting and he has an error code SYCE
i advised him to unplug the unit a wait a few minuets. he did and it reset. and worked fine
a week later we have the same issue i cam by the fan in the freezer seems to be working i reset the unit and it worked fine again.
how do we prevent the V error code from happening again?

When put on normal wash the interface push buttons the lights go on. If you it cancel pump runs to drain the unit. Then put normal wash and it start the lights are lit up for right cycle 5 seconds later they will all go out. Like there is no power on the unit? My question is it the interface board or the control unit?

so the compressor is dead.
can you please tell me how i change it?
maybe a video instructions

Everything else works but there’s no water coming into the machine. I have checked the water hose and there is water in the line I have tested the water inlet valve for continuity I’m getting 0.808 ohms of resistance does that mean the water inlet valve is faulty and if it is good what else can be the problem thank you

So it takes a long time for it to preheat the igniter is fine after some time the oven shuts off but the preheat light remains on