Brand: GE (General Electric)

THE UNIT ISN’T COOLING, THE MAIN BOARD HAS BEEN REPLACED AND THE COMPRESSOR IS RUNNING. I DON’T HAVE ANY PAPERWORK, IF YOU COULD TRY TO FIND THE COMPLETE SERVICE MANUAL I’D APPRECIATE. THANKS

Homeowner said that a technician came out previously because the display was blank and the technician the display board.
However when you put in the new board it displayed 555 on the freezer section and 999 on the refrigerator section.
Everything is working fine the unit is freezing and cooling however the buttons on the panel are not functioning.
Meaning I cannot change the temperature to anything I cannot shut the unit off besides for unplugging the unit.
I did on plug unit for quite a few minutes hoping that it would reset the control but it did not it returns to the same display

I TRY TO REEPLECE THE INTERFACE WATER DISPENSER U HAVE ANY VIDEO O TECH SUPPORT

Could it be a bad motor sensor ?

Hello, have a GE gas oven set to bake @ 350 starts to preheat will only reach 250 and oven shuts itself off. Try it again same thing, shuts its self off at 250 as if you hit the cancel button. Clock stays lite up. I tried self clean cycle and it seemed to work ok, door locked, fan started running. I stopped it before it got too hot so I could get the door to unlock without having to wait for the oven to cool down. Tried the broiler burner
, it seemed to be working ok. Tried bake again at 350 and it reached 350 with out shutting off. I thought great its working. Tried bake the next day same problem, oven shuts its self off at 250 wont go any higher. Is there some special setting or feature on this oven causing this???? Made sure the keep warm setting was off.

so i figured it maybe the control board so i changed it.
when i return power to the unit the bake and prob lights were flashing nothing seems to work and then the f7 error came back non
please advise

Parts break down of unit.

GOOD EVENING. I AM TOLD THAT THE WASHER DOES NOT FILL WITH ENOUGH WATER. I HAVE NEVER WORKED ON A WASHER IN A STACK AND I AM NOT SURE ON HOW TO DISASSEMBLE THE UNIT. ANY HELP WOULD BE GREAT, THANKS, TODD FROM NY.

THE COMPRESSOR IS RUNNING AT -1.7inHg. NEITHER EVAPORATOR FAN IS RUNNING AND IT’S NOT COOLING. I HAVEN’T WORKED A LOT ON THESE VARIABLE SPEED UNITS. I GUESS I NEED TO FIND THE DIAGNOSTIC SHEETS AND WHAT EVERY ELSE YOU COULD DIG UP. TX

does not dispense water
does not dispense ice

Diagnose why washer will not spin?

The dispensor control board keeps blinking 0 37 no led lights on in fridge and freezer. Unit still running and cooling. Able to get lights back on but then go out again. Nothing dispensing either.

My customer called me up and said that she heard a noise coming from the back of the fridge. Loud vibrating noise. The temp in the freezer was ok, but the fridge was high. I asked her if there was frost build up on the back of the freezer, she said no. She unplugged it. I stopped by, checked the continuity on the freezer evap fan, and hot none.
So, I bought a new one, put it in. It doesn’t seem to be working either. No air movement.

I CLOSE THE DOOR ON CUSTOMERS D/W AND BREAKER TRIPS WITH NO DRAMA RESET DISPLAY LIGHT AS NORMAL CLOSE DOOR BREAKER TRIPS IM NOT A NEWBIE BUT THIS PARTICULAR MODEL IS KIND OF COMPLICATED ANY HELP WOULD BE GREAT THANK YOU

GE Profile dishwasher about 9 years old. The keypad is not lighting up or responding to the basic wash cycles. Heat Dry and Normal are the only lights that work on the keypad.

Appliance has been unplugged and elect outlet checked. Thoughts?

REFRIGERATOR NOT COOLING. COMPRESSOR RUNING AND ALL THE FANS. EVAPORTOR was build up with ice about 2 level of the core. Door display is 0 degrees on the freezer, 69 on the fresh food. change both sensers . That didnt change anything. this refrigerator has 2 evaporates. then i check the pressure on the low side. 25 psig and run at .68 amps. i charge it up till the amps got up to 1.03. 5 psig now. Left it like that till tomorrow. what do you thing about that.

Hi, I changed the ERC with a new one. Connect power to oven and clock powers up, then Loc rEF shows. Touch pad seems locked out. The ERC has a sticker on it that says important to set glass touch reference point. See mini manual for procedure. I do not have this mini manual. There is a part no. on the sticker 205c2793p001, don’t know if this is a good no. I’m not sure if this is what I have to do to get rid of the code and make the oven work properly. I have located the Tech sheet, says nothing about above procedure. Need help, Thanks Jim.

Looking for some info on this.

The appliance is only run approximately every 2 weeks as there are only 2 of us seniors in the household. I made all the selections as normal and selected the start, closed the door immediately, and shortly afterward the light started flashing and the beeper comes on. I have canceled the program multiple times and re-selected different programs to see if made any difference, but the same results occurred once the door was shut. I have check all the filters to ensure they are clean. I do not have an electrical schematic to see if there are any other permissive interlocks that could be holding the start initiation sequence out.

watched your video, ordered a new capacitor and relay module. Installed new unit same issue. Any other solutions? Refrigerator is only 13 months old.

THE COMPRESSOR IS DRAWING 1.4 AMPS AND ALL FANS ARE RUNNING. I INSTALLED A SERVICE VALVE ON THE PROCESS STUB AND IT IS READING 70 PSIG. I DON’T HAVE A VALVE ON THE HIGH SIDE. THE PRESSURE DOESN’T MOVE WHEN THE UNIT IS UNPLUGGED. THERE WEREN’T ANY SERVICE VALVES PRIOR TO ME ADDING THE ONE. IS THIS AN INDICATION OF A BLOCKAGE, BAD COMPRESSOR OR SOMETHING ELSE. I’M RELATIVELY NEW TO REFRIGERATION AS MOST OF MY EXPERIENCE IS WITH A/C. THE UNIT IS NOT COOLING AT ALL. THE COMPRESSOR FEELS VERY HOT AS WELL.

Hot air entering icemaker in one vent hole on side causing ice warm air to get in and puddle in bin causing ice to melt. Burn makes are around this vent hole as well. About every 3 weeks they will get ice. Rest of fridge is running normal.

My vent hood is making a grinding noise.

lid will not close

NOT HEATING ANY AREA (OVEN OR BURNERS)

it seems that the microwave needs a new mag tube and diode.

IS THERE A TECH SHEET HIDDEN SOMEWHERE ON THIS UNIT, IF NOT CAN YOU GET ME ONE? i HAVE AN ICEMAKER NOT WORKING.