Brand: Kenmore

I have a kenmore elite HE4 that will run for a while until it get very hot and cuts off. I have checked the thermo cutoff fuse, the heating element, thermostat high limit, and thermo cut off per your videos. Everything shows continuity with the meter. I have noticed that the heating element does not cycle on and off per your video. For what it is worth, it does not look like the entire heating coil itself is red either. There is an inch or two of it that does not look red to me. Is it possible there is an issue with the heating element that I am missing.

What would cause this Oasis to shake violently during the spin cycle? It shakes so much, that it hits the sides of the outer casing. And the board reads Ul.

Dishwasher motor doen’t run, Drain works when you it cancel. Unit won’t go into diagnostics. Is there a video that shows you how. I tried any key 3 consecutive times within 1 sec. closed the door. won’t go into diagnostics. Does the tubulity sensor have anything to do with motor running? I’m sure if i’m doing it right to put to diagnostics. They say it has to be in stand by mode. Is stand by mode the pause button or is it with the door open and the start button pushed. It would be really helpfull if they have video on how to put into diagnostics.

i checked the pump for blockage
(none), for twisted hoses(none), for if motor is spinning the pump(it does) . i don’t know what else to do?

dryer not heating , changed thermal fuse DC47-00016A worked hour later customer called no working agian .

REFRIGERATOR IS A FRENCH DOOR WITH DRAWER FOR FREEZER. THE FREEZER IS NOT FREEZING.
What will be the possible causes?

The referidge side is not cooling after 5 years. Freezer side is cold. Fan is working on freezer side, not fridge side.

water is staying at one level

There is Frost On the coils in the back of the freezer I check the the heating sensor for continuity I’ve got a resistance reading of 200 however I check the heating element for continuity I manually put the machine into the forest and nothing happens

after I purchased my new home I cleaned my refrigerator and freezer out really good and I think I may have got water somewhere and potentially blew a fuse because before I cleaned it the ice dispenser and water dispenser both work finethe ice maker control light blinks twice stops for one second then repeats I’ve made sure that there was no obstruction to the optical part and still blinks twice what is the problem?

I set my washer to run, it fills with water, starts to wash and the timer advances to completion in about 3 minutes. It does not do the spin cycle but he states it does drain. Any ideas what this might be? Thank you in advance.

I removed a ceramic piece of dishware from the drain pump, the unit drains really slowly now. I made sure nothing was in the drain hose and explained to the customer the debris caused an issue with the pump. The unit also needs a new heating element which I had on me. Do you guys carry the pump? They opted not to have it done right away but I have a feeling I’ll be getting a call back soon to do it since any debris or foreign objects are going to slow down that drain pump even more. Really appreciate you guys being available to help us on the weekends! Unheard of in most service industries.

My gas Kenmore range will not preheat.

My Kenmore dryer is not heating

My Kenmore washer will not spin or agitate. I see little plastic and rubber pieces on the floor under the washer . What cold this be ?

My electric Kenmore dryer is not heating properly.

My Kenmore refrigerator is not cooling is the fresh food section and has frost on back coil.

no stove top action, oven works great,,,,, whats a poor boy to do ???? seriously,,, where can I look up codes?

the two lights were and the unit would not do anything.
I turned of the power and disconnected the ribbon and then reconnected it.
the unit started to work.
buy I still see the lights slightly on

I have a Kenmore Refrigerator that is not working.

The ice chute on my refrigerator is frosting up.